Amit Harenkumar Munshi

Amit Harenkumar Munshi

Auto-generated profile, based on publicly available information

Amit Harenkumar Munshi

Department of Mechanical Engineering, Colorado State University, Fort Collins, CO 80523, USA

Research Focus & Metrics

Academic Career Length

13Years (2014-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
13 May 2019 in Nature Energy
Verified
Journal Article
Open access
PDF file
TFThomas A. M. Fiducia
Thomas A. M. Fiducia
BMBudhika G. Mendis
Budhika G. Mendis
KLKexue Li
Kexue Li
CGChris R. M. Grovenor
Chris R. M. Grovenor
AMAmit H. Munshi
Amit H. Munshi
JWJohn Walls
John Walls
Electricity produced by cadmium telluride (CdTe) photovoltaic modules is the lowest-cost electricity in the solar industry, and now undercuts fossil fuel-based sources in many regions of the world. This is due to recent efficiency gains brought about by alloying selenium into the CdTe absorber, which has taken cell efficiency from 19.5% to its current record of 22.1%. Although the addition of selenium is known to reduce the bandgap of the absorber material, and hence increase the cell short-circuit current, this effect alone does not explain the performance improvement. Here, by means of cathodoluminescence and secondary ion mass spectrometry, we show that selenium enables higher luminescence efficiency and longer diffusion lengths in the alloyed material, indicating that selenium passivates critical defects in the bulk of the absorber layer. This passivation effect explains the record-breaking performance of selenium-alloyed CdTe devices, and provides a route for further efficiency improvement that can result in even lower costs for solar-generated electricity.

7 December 2017 in IEEE Journal of Photovoltaics
Verified
Journal Article
Open access
AMAmit H. Munshi
Amit H. Munshi
JKJason Kephart
Jason Kephart
AAAli Abbas
Ali Abbas
JRJohn Raguse
John Raguse
JBJean-Nicolas Beaudry
Jean-Nicolas Beaudry
WSWalajabad Sampath
Walajabad Sampath
An 800 nm CdSeTe layer was added to the CdTe absorber used in high-efficiency CdTe cells to increase the current and produce an increase in efficiency. The CdSeTe layer employed had a band-gap near 1.41 eV, compared with 1.5 eV for CdTe. This lower band-gap enabled a current density increase from approximately 26 to over 28 mA/cm2. The open-circuit voltage obtained in the high-efficiency CdTe-only device was maintained and the fill-factor remained close to 80%. Improving the short-circuit current density and maintaining the open-circuit voltage lead to device efficiency over 19%. External quantum efficiency implied that about half the current was generated in the CdSeTe layer and half in the CdTe. Cross-sectional STEM and EDS showed good grain structure throughout. Diffusion of Se into the CdTe layer was observed. This is the highest efficiency polycrystalline CdTe photovoltaic device demonstrated by a university or national laboratory.

1 March 2018 in Solar Energy Materials and Solar Cells
Verified
Journal Article
Closed access
AMAmit H. Munshi
Amit H. Munshi
JKJason M. Kephart
Jason M. Kephart
AAAli Abbas
Ali Abbas
TSTushar M. Shimpi
Tushar M. Shimpi
Kurt L. BarthKurt L. Barth
Kurt L. Barth
WSWalajabad S. Sampath
Walajabad S. Sampath

18 January 2018 in IEEE Journal of Photovoltaics
Verified
Journal Article
Closed access
JKJason M. Kephart
Jason M. Kephart
AKAnna Kindvall
Anna Kindvall
DWDesiree Williams
Desiree Williams
DKDarius Kuciauskas
Darius Kuciauskas
PDPat Dippo
Pat Dippo
WSW. S. Sampath
W. S. Sampath
Commercial CdTe PV modules have polycrystalline thin films deposited on glass, and devices made in this format have exceeded 22% efficiency. Devices made by the authors with a magnesium zinc oxide window layer and tellurium back contact have achieved efficiency over 18%, but these cells still suffer from an open-circuit voltage far below ideal values. Oxide passivation layers made by sputter deposition have the potential to increase voltage by reducing interface recombination. CdTe devices with these passivation layers were studied with photoluminescence (PL) emission spectroscopy and time-resolved photoluminescence (TRPL) to detect an increase in minority carrier lifetime. Because these oxide materials exhibit barriers to carrier collection, micropatterning was used to expose small point contacts while still allowing interface passivation. TRPL decay lifetimes have been greatly enhanced for thin polycrystalline absorber films with interface passivation. Device performance was measured and current collection was mapped spatially by light-beam-induced current.

1 November 2018 in Solar Energy Materials and Solar Cells
Verified
Journal Article
Open access
AMAmit H. Munshi
Amit H. Munshi
JKJason M. Kephart
Jason M. Kephart
AAAli Abbas
Ali Abbas
ADAdam Danielson
Adam Danielson
GGGuillaume Gḗlinas
Guillaume Gḗlinas
WSWalajabad S. Sampath
Walajabad S. Sampath

1 October 2018 in Solar Energy
Verified
Journal Article
Closed access
AMAmit H. Munshi
Amit H. Munshi
NSNikhil Sasidharan
Nikhil Sasidharan
SPSubin Pinkayan
Subin Pinkayan
Kurt L. BarthKurt L. Barth
Kurt L. Barth
WSW.S. Sampath
W.S. Sampath
WOWeerakorn Ongsakul
Weerakorn Ongsakul