Morten Opprud Jakobsen

Morten Opprud Jakobsen

Auto-generated profile, based on publicly available information

Morten Opprud Jakobsen

Department of Electrical and Computer Engineering Aarhus University Finlandsgade 22 8200 Aarhus N Denmark

Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
7 July 2023 in Mechanical Systems and Signal Processing
Verified
Journal Article
Open access
MJMorten Opprud Jakobsen
Morten Opprud Jakobsen
EHEskild Sune Herskind
Eskild Sune Herskind
CPChristian Fischer Pedersen
Christian Fischer Pedersen
MKMikael Bergholz Knudsen
Mikael Bergholz Knudsen
This paper proposes a method for detecting insufficient lubrication in rolling bearings, by utilising a low cost MEMS ultrasonic microphone. We run a set of grease lubricated bearings under load, alternating between good and insufficient lubrication conditions by adjusting speed and temperature, over an 18 day experiment, followed by a short validation experiment on a different set of bearings on a secondary test rig . Vibration signals are recorded from an ultrasonic microphone, using a purpose built prototype sensor, then band-pass and high-pass filtered and subsequently analysed using statistical time-domain features. The viscosity ratio Kappa of the lubricant is used as a metric for quality of oil-film formation, and is calculated throughout the experiment from rotating speed and temperature. The results are compared with the predictions from a linear regression model and a simple Neural Network trained on ensembles of three and ten selected features. The three Hjorth’s Parameters activity, mobility and complexity calculated on high-pass filtered microphone signals from the experiments show a good correlation with the viscosity ratio Kappa. When combining these, using a Linear Regression model or a simple two layer Neural Network model, we are able to predict the viscosity ratio with good precision. The proposed method may be used to assess the quality of oil film formation in bearings during operation under varying speed and temperature conditions.

26 March 2024 in HardwareX
Verified
Journal Article
Open access
MJMorten Opprud Jakobsen
Morten Opprud Jakobsen
Vibration -based Condition Monitoring (CM) is an essential tool for identifying potential defects in industrial machinery. However, the implementation of an efficient CM system often necessitates the use of high -cost accelerometers with a large bandwidth. To address this challenge, this study introduces a low-cost CM sensor composed of an ultrasonic MEMS microphoneSPH0641LU and an ADXL1002 MEMS accelerometer. The combination of these two sensor types allows for comparative analysis of the captured data. The SPH641LU microphone is capable of detecting audible vibration signals with a frequency range up to 80 kHz, while the ADXL1002 accelerometer can measure vibrations up to 21 kHz. In addition a three axis ultra low power accelerometer is included, allowing measurement of unbalance or rotating speed, below 200Hz. Moreover, the sensor is designed to operate on battery power and provides the capability for raw data transmission via Bluetooth Low Energy (BLE) or the transmission of pre-processed features from the raw data using LoRaWAN.

1 April 2021 in Tribology International
Verified
Journal Article
Closed access
MJMorten Opprud Jakobsen
Morten Opprud Jakobsen
EHEskild Sune Herskind
Eskild Sune Herskind
Kim BjergeKim Bjerge
Kim Bjerge
PAPeter Ahrendt
Peter Ahrendt
CPChristian Fischer Pedersen
Christian Fischer Pedersen
MKMikael Bergholz Knudsen
Mikael Bergholz Knudsen

13 September 2023 in arXiv
Verified
Preprint
Open access
PDF file
CLChristian Marius Lillelund
Christian Marius Lillelund
FPFernando Pannullo
Fernando Pannullo
MJMorten Opprud Jakobsen
Morten Opprud Jakobsen
CPChristian Fischer Pedersen
Christian Fischer Pedersen
Ball bearings find widespread use in various manufacturing and mechanical domains, and methods based on machine learning have been widely adopted in the field to monitor wear and spot defects before they lead to failures. Few studies, however, have addressed the problem of censored data, in which failure is not observed. In this paper, we propose a novel approach to predict the time to failure in ball bearings using survival analysis. First, we analyze bearing data in the frequency domain and annotate when a bearing fails by comparing the Kullback-Leibler divergence and the standard deviation between its break-in frequency bins and its break-out frequency bins. Second, we train several survival models to estimate the time to failure based on the annotated data and covariates extracted from the time domain, such as skewness, kurtosis and entropy. The models give a probabilistic prediction of risk over time and allow us to compare the survival function between groups of bearings. We demonstrate our approach on the XJTU and PRONOSTIA datasets. On XJTU, the best result is a 0.70 concordance-index and 0.21 integrated Brier score. On PRONOSTIA, the best is a 0.76 concordance-index and 0.19 integrated Brier score. Our work motivates further work on incorporating censored data in models for predictive maintenance.