1 January 2007 in Journal of Environmental Engineering
Iron oxide impregnated onto an activated carbon has a high arsenic (As) removal capacity with the potential to be used in existing activated carbon column systems. Objectives of this research were to investigate removal from aqueous-phase systems using fixed-beds packed with and to determine if the triple layer model (TLM) with the homogeneous surface diffusion model (HSDM) could describe removal in the columns. Rapid small-scale column tests (RSSCT) were conducted at various empty bed contact times (EBCT). Effluent breakthrough was incipient for the 0.20-min EBCT experiment, whereas bed volumes of water at 1-mg/L inlet concentration of was treated at an EBCT of before breakthrough occurred. The TLM with three surface reactions coupled with the HSDM provided accurate prediction of removal in the RSSCT.
1 September 1997 in Separation Science and Technology
Granular activated carbon (GAC) has been used to remove organics and metals simultaneously from wastewaters (4). For a regeneration procedure to be effective on GAC containing both metals and organics, it must remove both the metals and organic compounds. In this study, GAC saturated with Pb and phenol was regenerated using an NaOH rinse in batch mode. Four variables were investigated: 1) regenerant concentration (0, 0.1, and 1.0 N), 2) regenerant to carbon mass ratio (5:1 and 10:1), 3) regenerant temperature (22 and 80°C), and 4) regeneration time (0.33, 1, 3, 7, and 21 days). Maximum regenerations of 47% for Pb and 48% for phenol were observed. The 1.0 N NaOH regenerated a higher percentage of both Pb and phenol when compared to the other regenerants. The 10:1 regenerant to carbon ratio resulted in increased regeneration over the 5:1 regenerations. Pb regeneration was slightly higher at 80°C than at 22°C whereas phenol regeneration was slightly lower at 80°C than at 22°C. Maximum regenerations for both Pb and phenol were observed within the first day of regeneration, in most cases within the first 8 hours.
15 September 2010 in Separation Science and Technology
The ability of an iron-impregnated ion exchange bead (PWX5) to remove As(V) from ground water was investigated. The effects of particle size, solution pH, As(V) concentration, competition, adsorbent concentration, temperature, iron content, and iron accessibility on removal kinetics and/or equilibrium were determined. PWX5's performance was compared to other iron-based adsorbents, primarily Bayoxide® E-33 (E-33), a granular ferric oxide, for arsenic removal performance. All of the factors cited impacted either the amount of As(V) adsorbed or the rate of adsorption. Stirred batch reactor data showed the rate of adsorption increased as particle size decreased and bottle point isotherm data showed As(V) adsorption maximum capacity increased with higher initial adsorbate concentration. The presence of phosphate and silicate reduced the amount of As(V) adsorbed as did a pH > 7.0. PWX5 is durable, rather homogeneous in size and effective at removing As(V). It is a viable alternative to E-33 which has a wider size distribution and wears more easily.
1 April 2022 in Environmental Science: Processes & Impacts
Many aqueous transition metals in PM precipitate in the DTT assay.
21 December 2020 in Environmental Science: Processes & Impacts
Transition metals are thought to be among the most toxic components in atmospheric particulate matter (PM) due to their role in catalyzing reactive oxygen species (ROS) formation. We show that precipitation of the transition metals Fe(II), Fe(III), and Mn(II) are thermodynamically favored in phosphate-based assays used to measure the oxidative potential (OP) – a surrogate for toxicity – of PM. Fe and Mn precipitation is likely to occur at extremely low metal concentrations (100 μM) with visible precipitates provide quasi-validation of the thermodynamic modeling. Oxidation of Fe(II) to Fe(III) is likely to be rapid in all in vitro OP assays, transforming Fe to a much less soluble form. Fe precipitates are likely to increase the rate of precipitation of other metals and possibly induce co-precipitation. These results have direct relevance for all PO4-based assays; the implications for studies of PM toxicity are discussed.
1 May 2013 in Journal of Environmental Engineering
Ferrate [Fe(VI)] and alkaline chlorination (AC) were investigated for the treatment of a maritime wastewater (CN, Cd, Cu, Ni, Pb, and Zn) in a seawater matrix. AC reduced CN concentrations but large dosages were required (0.018–0.056 mol CN consumed/mol HOCl). Metal removal occurred during the first stage () but the amount of sludge produced was large due to formation. Fe(VI) was effective in oxidizing CN and removing heavy metals to low levels without pH adjustment. Fe(VI) requirements [] were higher than those observed for other wastes but are considered more manageable compared with HOCl. Metal removal occurred by adsorption and coprecipitation with Fe(III) oxide, which results from the oxidation of Fe(VI). During staged treatment, metal removal and CN destruction increased [2× for Cd, 3× for Cu, 2.7× for Ni, 0.12 to 0.18 mol CN consumed/mol Fe(VI)]. Fe(III) oxide was relatively easy to separate using ultrafiltration tubular membranes and the amount of sludge produced is much less than what would occur with AC. The Fe(III) oxide was separated using ultrafiltration with the amount of sludge produced much less than AC.