25 December 2021 in Plasma Physics and Controlled Fusion
A newly developed tool to simulate a tokamak full--discharge is presented. The tokamak "flight--simulator" Fenix couples the tokamak control system with a fast and reduced plasma model, yet realistic enough to take into account several of the plasma non--linearities. Distinguishing feature of this modeling tool is that it only requires the Pulse Schedule (PS) as input to the simulator. The output is a virtual realization of the full discharge, which time traces can then be used to judge if the PS satisfies control/physics goals or needs to be revised. This tool is thought for routine use in the control--room before each pulse is performed, but can also be used off--line to correct PS in advance, or to develop and validate reduced models, control schemes, and in general the simulation framework.
18 November 2021 in Nuclear Fusion
Predicting the impact of heating and current drive (H&CD) sources is essential to evaluate the performance of ITER plasmas and to subsequently optimise the scenarios for the four stages of the ITER research plan. This should be done in the context of global transport calculations of complete plasma discharges. For this purpose, a dedicated workflow has been developed in the ITER integrated modelling and analysis suite as a modular component to be used together with transport solvers to quantify the dynamics of H&CD sources for the different phases of a plasma discharge, including possible synergetic effects between the heating sources. This paper presents the results of the combined modelling of H&CD sources for the ITER DT baseline 15 MA/5.3 T scenario including the synergy between neutral beam injection (NBI) of deuterium, fusion-born alpha particles and ion cyclotron resonance heating (ICRH) at the fundamental frequency of deuterium, showing modest synergetic effects. The results of the combined H&CD sources for an ITER 7.5 MA/2.65 T helium plasma of the second pre-fusion power operation phase (PFPO-2) are also shown, exhibiting more significant synergetic effects between the fundamental ICRH minority hydrogen heating and NBI hydrogen beams. Finally, a study of electron cyclotron heating absorption for an ITER helium PFPO scenario at 7.5 MA/2.65 T is also presented with a discussion on the edge parasitic absorption that arises under specific conditions.
21 September 2006 in Review of Scientific Instruments
Two devices have been installed in the Joint European Torus (JET) vacuum vessel near the plasma boundary to investigate the loss of energetic ions and fusion products in general and alpha particles in particular during the upcoming JET experiments. These devices are (i) a set of multichannel thin foil Faraday collectors and (ii) a well collimated scintillator, which is optically connected to a charge-coupled device. Initial results including the radial energy and poloidal dependence of lost ions from hydrogen and deuterium plasmas during the 2005-06 JET restart campaign will be presented.
28 July 2010 in Nuclear Fusion
Energy and pitch angle resolved measurements of highly energetic (megaelectronvolt (MeV) range) suprathermal ions ejected from the plasma through interaction with fishbone oscillations are presented. The measurements are obtained with a 2D scintillator probe diagnostic installed on JET, which is designed to detect lost ions only above a certain energy threshold (E min,D ∼ 200 keV). In the case reported here the lost ions are identified as fast protons which had been accelerated to high energies by ICRF minority heating. The energy of the lost protons (∼0.5–4 MeV) is approximately one order of magnitude higher than the energy of the injected beam ions (maximum 130 keV) driving the fishbone. Losses arriving at the probe are enhanced by about a factor 10–20 with respect to MHD-quiescent levels, and are found to increase quadratically with the fishbone amplitude. Using a number of simplifying assumptions, numerical simulations have been performed which combine the HAGIS, MISHKA and SELFO codes (where the distribution function predicted by SELFO has been validated against neutral particle analyser measurements). The losses are found to originate from orbit stochastic diffusion of trapped protons near the plasma boundary or from counter-passing protons deep in the plasma core, which transit under the influence of the fishbone into an unconfined trapped orbit. The simulations show further that the losses are of non-resonant type. The simulated energy and pitch angle distribution of the losses, the temporal behaviour of the losses during a fishbone cycle and the scaling of the losses with the fishbone amplitude are compared with experiment. The simulation results are mostly in broad agreement with experiment, but some of the predictions could not be reconciled with experiment using this model.
21 February 2022 in Plasma Physics and Controlled Fusion
This paper presents recent progress in studies of neoclassical tearing modes (NTMs) on TCV, concerning the new physics learned and how this physics contributes to a better real-time (RT) control of NTMs. A simple technique that adds a small (sinusoidal) sweeping to the target electron cyclotron (EC) beam deposition location has proven effective both for the stabilization and prevention of NTMs. This relaxes the strict requirement on beam-mode alignment for NTM control, which is difficult to ensure in RT. In terms of the EC power for NTM stabilization, a control scheme making use of RT island width measurements has been tested on TCV. NTM seeding through sawtooth (ST) crashes or unstable current density profiles (triggerless NTMs) has been studied in detail. A new NTM prevention strategy utilizing only transient EC beams near the relevant rational surface has been developed and proven effective for preventing ST-seeded NTMs. With a comprehensive modified Rutherford equation (co-MRE) that considers the classical stability both at zero and finite island width, the prevention of triggerless NTMs with EC beams has been simulated for the first time. The prevention effects are found to result from the local effects of the EC beams (as opposed to global current profile changes), as observed in a group of TCV experiments scanning the deposition location of the preemptive EC beam. The co-MRE has also proven able to reproduce well the island width evolution in distinct plasma scenarios on TCV, ASDEX Upgrade and MAST, with very similar constant coefficients. The co-MRE has the potential to be applied in RT to provide valuable information, such as the EC power required for NTM control with RT-adapted coefficients, contributing to both NTM control and integrated control with a limited set of actuators.
26 March 2024 in Nuclear Fusion
ETEurofusion Tokamak Exploitation Team
Eurofusion Tokamak Exploitation Team
+16
The successful operation of fusion reactors requires plasma scenarios with good core confinement and acceptable first wall heat loads that are stable and robust to external perturbations. This poses both physical and technological challenges. One of the technologies that addresses these challenges is a complex feedback control system that supports advances in physical understanding and helps to ensure stable operating conditions. The operation of marginally stable plasmas often leads to off-normal events (such as disruptions) and feedback control can prevent these to some extent. This contribution gives an overview of the main results of the development and operation of the feedback control algorithms on ASDEX Upgrade (AUG). Fueling actuators, using a combination of gas valves and pellet injection, can simultaneously control neutral density of the divertor and the density of the plasma core above the Greenwald limit. Impurity injection is employed to control the position of the X-point radiator, allowing the creation of an ELM-suppressed H-mode with high radiation fraction. Heating actuators are used to control the plasma energy content, which supports advanced tokamak experiments and enables stable I-mode operation, and the electron temperature control, which supports turbulence studies. In control technology, AUG has pioneered the use of virtual actuators, which allow effective use of the limited number of heating actuators, adaptive control policies, and exception handling. Such technologies will also be used in ITER. Advanced nonlinear state observers (RAPTOR, RAPDENS) and codes to evaluate the power deposition properties (RABBIT, TORBEAM) are available for routine use in the AUG feedback controllers. Extensive use of the AUG discharge control system further enhances the research capabilities of this machine.