Ali R. Vatankhah

Ali R. Vatankhah

Auto-generated profile, based on publicly available information

Ali R. Vatankhah

Univ. of Tehran

Research Focus & Metrics

Academic Career Length

26Years (2001-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 September 2011 in Journal of Hydraulic Engineering
Verified
Journal Article
Closed access
AHA. Habibzadeh
A. Habibzadeh
AVAli R. Vatankhah
Ali R. Vatankhah
NRN. Rajaratnam
N. Rajaratnam
A theoretical method was used to derive an equation for the discharge coefficient of sluice gates in rectangular channels under orifice-flow (both free and submerged) conditions. The proposed equation allows for the effects of energy dissipation between the upstream section of the gate and the vena contracta. The hydraulic energy loss in the upstream pool is attributable to the induced turbulence by the recirculating region and to the growth of bottom boundary layer. For the submerged-flow condition, turbulent shear-layer entrainment is also responsible for the energy loss. This energy loss is introduced into the equations through a coefficient k that has been conventionally assumed to be negligible. Experimental data from the literature were used to validate the equation, which showed good agreement with the measured values. It is also shown that the magnitude of the energy-loss factor is a function of the geometry of the gate and can modify the discharge coefficient. An equation for the distinguishing c...

1 June 2010 in Flow Measurement and Instrumentation
Verified
Journal Article
Closed access
AVAli R. Vatankhah
Ali R. Vatankhah

1 May 2018 in Journal of Hydraulic Engineering
Verified
Journal Article
Closed access
AVAli R. Vatankhah
Ali R. Vatankhah
Friction factor determination is important for modeling fluid flows in pipes. The Colebrook equation has been widely used for estimating the pipe friction factor in fully developed turbulent regime. Because of the implicit nature of Colebrook equation, various regression-based approximations, Lambert W-function-based solutions, series-based solutions, and analytical approximations are developed for explicitly determining the friction factor. This study focuses on approximate analytical solutions for the Colebrook equation with a minimum number of natural logarithms and noninteger powers (lower computational cost). For this, a new mathematically equivalent representation of the Colebrook equation is presented. This form consists of two nonlinear equations which are very well suited for developing the analytical solutions for the friction factor. The simple analytical solutions developed in this study with the maximum relative errors less than 0.85, 0.25, 0.054, and 0.0028% (solutions with different degrees of accuracy) are among the most accurate analytical approximations to the Colebrook equation. Simple form and superior efficiency of the proposed solutions make them preferable to currently available approximate solutions to the Colebrook equation.

31 March 2011 in Flow Measurement and Instrumentation
Verified
Journal Article
Closed access
AVAli R. Vatankhah
Ali R. Vatankhah
SESaid M. Easa
Said M. Easa

1 October 2018 in Journal of Irrigation and Drainage Engineering
Verified
Journal Article
Closed access
AVAli R. Vatankhah
Ali R. Vatankhah
SMS. H. Mirnia
S. H. Mirnia
Weirs, orifices, baffle sluice gates, and sluice gates are widely used in irrigation networks for distributing water from the source to irrigated areas. Side orifices are generally placed in the side of a channel for diverting some of the source channel flow. Prediction of the discharge rate through side orifices of different shapes is important in irrigation and hydraulic engineering. The hydraulic behavior of side triangular orifices (Δ-shape orifices) has not been studied either experimentally or theoretically. In this study, sharp-crested side triangular orifices are studied experimentally and analytically. Several models are derived for the discharge coefficient based on Buckingham’s theorem of dimensional analysis. A series of laboratory experiments (570 runs) were performed to investigate the flow discharge through side triangular orifices located in horizontal rectangular channels under free flow conditions. Using the collected data in the present work, proposed models were calibrated. One model that includes the approach Froude number has an average error of 2.1%, while a second model that does not include the approach Froude number has an average error about 3.3%. Therefore, actual discharge through the side triangular orifices can be accurately estimated using the proposed models.

1 March 2012 in Flow Measurement and Instrumentation
Verified
Journal Article
Closed access
AVAli R. Vatankhah
Ali R. Vatankhah