A broadband low-profile high-gain folded transmitarray antenna (FTA) is proposed to generate orbital angular momentum (OAM) with circular polarization. A chiral metasurface is employed as the top layer with the function of reflecting anticipant circularly polarized (CP) incident waves while transmitting the orthogonal ones. The geometric phase is then introduced to achieve 360° coverage of the transmission phase without affecting the reflection one. To obtain a high-gain and compact planar source, a 2 × 2 patch antenna array, integrated with the bottom metallic ground, is selected as the feed. Two proof-of-concept prototypes for vortex beam generation are constructed and experimentally measured. Both simulated and measured results demonstrate that l =–1 and l =+1 OAM mode beams can be generated from 8.7 GHz to 9.5 GHz, and the measured maximum gains for l =–1 and l =+1 reach 18.1 dBi and 18.3 dBi with the corresponding peak aperture efficiencies of 6.1% and 6.4%, respectively. Meanwhile, the axial ratios (ARs) of the peak of far-field patterns are less than 3 dB over the entire operating frequency range, providing broadband CP vortex beams. The proposed high-gain low-profile broadband FTA antenna shows a promising perspective in OAM-based wireless communication.
10 September 2018 in IEEE Transactions on Components, Packaging and Manufacturing Technology
Three-line coupled structure (TLCS) is employed in the design of filtering power divider (FPD) to achieve a broad fractional bandwidth and good frequency selectivity in this paper. Detailed theoretical analysis of the proposed FPD is presented by using the calculated method of impedance matrix deduction. To validate the design concept, the proposed initial FPD prototype is electromagnetically simulated, whose performance shows good consistence with that of the proposed theoretical calculation. Additionally, a simple quasi-lumped impedance transformer is introduced near the input port to further improve the matching status of the FPD. These two above FPDs are both designed with the center frequencies of 2.42 GHz and 3-dB fractional bandwidths of over 82.6%, the latter one of which is fabricated and tested. Comparisons between the simulated and measured results are presented with good agreement to verify the calculated predications.
21 December 2018 in IEEE Transactions on Antennas and Propagation
Since the earth is spherical in shape, the paths from the satellite to various points on the earth are different in both the distance and atmospheric attenuation. In order to maintain approximately uniform effective signal strength on the surface of the earth, the radiation pattern of the antenna should be formed according to the shape of the earth. Former antennas for earth coverage are either bulky or hard to realize the desired beam pattern within a wide angle range, thus are not suitable for small satellite. To solve this problem, this paper presents a novel circularly polarized earth coverage antenna for spaceborne applications. The proposed antenna consists of a specially designed dielectric cylinder, in which a cavity backed patch antenna is embedded. With the help of the concave structure at the top of the dielectric cylinder, the refraction of electromagnetic wave can be controlled, and then the radiation pattern is shaped. A sequentially feeding network is designed to drive the antenna. To verify our concept, a prototype is fabricated and experiments are carried out. The simulation agrees well with the measurement. The earth coverage radiation pattern is obtained within the beamwidth of θ in the range of ±50° with the measured space axial ratio is better than 3 dB from 4.9 GHz to 5.2 GHz. The measured peak gain is about 3.45 dBic at the elevation angle of ±50°.
This paper presents a wideband circularly polarized (CP) antenna based on two Vivaldi antenna elements. The two elements are orthogonally placed for compact consideration and driven by a specially designed wideband feeding network that splits the input signal into two-way signals with equal magnitude and orthogonal phase. In order to avoid crossing of the feeding lines of two Vivaldi elements, a small shift between them is introduced. This, however, will result in the undesired phase difference of two Vivaldi elements inevitably. To compensate the phase difference and ensure a wide AR bandwidth, the feeding network is specially designed. Besides, to make full use of the antenna space, the feeding network is placed on the surface of two Vivaldi elements. For demonstration purpose, a prototype is fabricated. The measured results show a -10 dB impedance bandwidth of 101.3% (2.35 GHz to 7.18 GHz) and 3 dB axial-ratio (AR) bandwidth of 118.4% (2.05 GHz to 8 GHz), and the maximum realized gain is 7.5 dBic. Meanwhile, stable radiation patterns are achieved with the cross-polarization lower than -20 dB across the wide operating bandwidth at boresight direction.
11 January 2023 in IEEE Transactions on Antennas and Propagation
This paper presents a wideband millimeter-wave (MMW) fan-beam antenna with a flat-top, rapid cutoff radiation pattern and beam scanning capability through the use of 3-D printer technology. The proposed antenna, consisting of several periodic structure that composed of dielectric and air slabs, is fed by the WR-28 waveguide. By tunning the ratio of dielectric slab thickness to that of unit cell, the effective permittivity is controlled flexibly. The phase distribution on the aperture is carefully modulated in this way to devote high-quality flat-top patterns. Additionally, the beam can be continuously scanned within the angle range of 70° without scarifying the gain performance dramatically. For demonstration, a prototype with boresight fan-beam radiation is first fabricated and measured. The proposed antenna achieves an impedance bandwidth of 50% from 24 to 40 GHz. Measured results indicate that the wide beamwidth patterns show flat-top and sharp cutoff performance. Both E-plane and H-plane patterns draw low cross-polarization (smaller than -22 dB). Another prototype, aiming to verify the beam scanning capability, is investigated. Measured results demonstrate the performances of the proposed antennas. With such favorable electrical performance, simple structure, and low-cost fabrication, the proposed antenna is a promising candidate for 5G MMW and satellite applications.
28 November 2018 in IEEE Transactions on Antennas and Propagation
This paper presents a novel differentially fed dual-polarized magnetic dipole antenna with stable radiation pattern, platform independence, wide bandwidth, and robust structure for spaceborne applications. The proposed antenna is formed by a dual-polarized magnetic dipole backed by a specially designed rectangular cavity. The magnetic dipole consists of two perpendicular parallel-plate waveguides with stepped edges to broaden the impedance bandwidth, providing good structural reliability which is critical to spaceborne antennas. A cross-shaped conductor fed by two pairs of capacity coupling feeding probes is utilized to drive the dual-polarized magnetic dipole antenna. The specially designed rectangular cavity has four metal plates in four corners to shape the radiation pattern at E- and H-planes. Furthermore, thanks to the cavity, the size of the conducting platform that the antenna mounted on has limited impact on antenna's electrical performances, particularly the radiation pattern. A prototype is fabricated and tested. Measured results show that the antenna achieves a fractional bandwidth of 18.5% with -10 dB reflection coefficient. The realized gain is about 8.5 dBi. A stable radiation pattern with a 3 dB beamwidth of 70° ± 3° and -4 dBi maximum beamwidth of 152° is observed. The measured cross-polarization is lower than -20 dB within ±65°. Measured results are in good agreement with simulation ones.