Mrutyunjay Nayak

Mrutyunjay Nayak

Auto-generated profile, based on publicly available information

Mrutyunjay Nayak

Solar Photovoltaics Laboratory, Department of Energy Science and Engineering, Indian Institute of Technology Delhi, New Delhi 110016, India

Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
7 August 2019 in Solar RRL
Verified
Journal Article
Closed access
PDF file
MNMrutyunjay Nayak
Mrutyunjay Nayak
SMSourav Mandal
Sourav Mandal
APAshutosh Pandey
Ashutosh Pandey
SMSapna Mudgal
Sapna Mudgal
SSSonpal Singh
Sonpal Singh
VKVamsi K. Komarala
Vamsi K. Komarala

28 April 2022 in IEEE Transactions on Electron Devices
Verified
Journal Article
Closed access
MNMrutyunjay Nayak
Mrutyunjay Nayak
VKVamsi Krishna Komarala
Vamsi Krishna Komarala
The thermal stability of molybdenum oxide ( ${\text{MoO}}_{x)}$ -based carrier selective contact silicon solar cells (Ag/ITO/MoO x /n-Si/LiF x /Al) is investigated under ambient annealing conditions for different time durations. The devices remain stable up to 150 °C for 15 and 30 min of annealing. However, at 200 °C, the cells degrade with a decrease in the fill factor and open-circuit voltage ( $V_{{\text {oc}}}$ ); the degradation rate is significant at 30 min. The illumination-dependent $V_{{\text {oc}}}$ study has indicated the charge transport barrier at the MoO x /c-Si interface in a degraded cell. The dark current density-voltage analysis of the degraded cells has also shown charge carrier recombination and series resistance at low- and high-forward bias conditions, respectively. To identify the device degradation with the temperature, ITO/MoO x and MoO x /c-Si interfaces are analyzed in terms of contact resistivity ( $\rho _{c}$ ) using extended transfer length method (ETLM). After annealing at 200 °C, a significant increase in $\rho _{c}$ of the MoO x /c-Si interface (from ~17 to $\sim 385~\text{m}\Omega $ -cm 2 ) is observed in comparison to the ITO/MoO x interface (from ~16.5 to $\sim 39~\text{m}\Omega $ -cm 2 ), reflecting the crucial role of MoO x /c-Si junction in cell degradation. The thermal degradation of the MoO x /c-Si interface is due to a decrease in the MoO x film’s work function (WF) upon annealing, which creates a transport barrier for charge carriers. The reduction in the MoO x WF results in misalignment of c-Si’s valence band and MoO x ’s conduction band, leading to inefficient carrier transport through band-to-band tunneling, which is also confirmed from the numerical simulations.

1 January 2022 in AIP Conference Proceedings
Verified
Conference Paper
Open access
PDF file
MNMrutyunjay Nayak
Mrutyunjay Nayak
APAshutosh Pandey
Ashutosh Pandey
SMSourav Mandal
Sourav Mandal
VKVamsi K. Komarala
Vamsi K. Komarala
Nickel Oxide (NiOx) based hole-selective contact silicon heterojunction (SHJ) solar cells are fabricated with SiOx and i-a-Si:H surface passivation layers. The power conversion efficiency (η) of ∼17.3% and open-circuit voltage (Voc) of ∼670 mV is achieved from the cell with i-a-Si:H layer compared to η of ∼15.26% and Voc of ∼580 mV with SiOx layer. The significant improvement in Voc of the cell with i-a-Si:H layer is due to better passivation of the silicon surface dangling bonds than the wet chemically grown SiOx layer. Whereas, slightly better short-circuit (Jsc) of ∼1.5 mA/cm2 from the cell with SiOx layer is observed due to minimization of parasitic absorption in the NiOx layer, which is also confirmed by quantum efficiency analysis. The contact resistivity measurements with p-c-Si/NiOx and n-c-Si/NiOx structures are also carried out to verify the hole selectivity properties of the NiOx film. The simulation results with NiOx hole selective layer show a large window to optimize the ITO layer's electronic properties without compromising the device's performance compared to p-a-Si:H hole-selective SHJ cell.

1 May 2021 in Solid-State Electronics
Verified
Journal Article
Closed access
KSKrishna Singh
Krishna Singh
MNMrutyunjay Nayak
Mrutyunjay Nayak
DSDipak Kumar Singh
Dipak Kumar Singh
VKVamsi K. Komarala
Vamsi K. Komarala

2 May 2024 in Semiconductor Science and Technology
Verified
Journal Article
Closed access
MNMrutyunjay Nayak
Mrutyunjay Nayak
APAshutosh Pandey
Ashutosh Pandey
SMSourav Mandal
Sourav Mandal
VKVamsi Krishna Komarala
Vamsi Krishna Komarala
The origin of the low-frequency inductive loop in the Nyquist plot of the Ag/indium tin oxide (ITO)/p-a-Si:H/intrinsic hydrogenated amorphous silicon (i-a-Si:H)/c-Si/i-a-Si:H/n-a-Si:H/ITO/Al heterojunction (SHJ) solar cells and their effect on the device performance are investigated by adopting impedance spectroscopy under dark and light. The negative capacitance/low-frequency inductive loop originates from the depopulation of injected charge carriers due to a transport barrier at the p-a-Si:H/ITO interface. The p-a-Si:H hole-selective SHJ device with a low-frequency inductive loop also has shown an S-shape and associated performance degradation in the light current density–voltage characteristics due to the opposing field type transport barrier present at the p-a-Si:H/ITO interface, which was overcome after vacuum annealing at ∼200 °C. However, the NiO x -based hole-selective contact Ag/ITO/NiO x /i-a-Si:H/c-Si/i-a-Si:H/n-a-Si:H/ITO/Al SHJ cells have not shown any low-frequency inductive loop or corresponding S-shape and associated performance degradation due to the optimised contact (minimum resistance) between the NiOx and ITO layers.

4 April 2023 in Physica Status Solidi (a)
Verified
Journal Article
Closed access
MNMrutyunjay Nayak
Mrutyunjay Nayak
KBKristin Bergum
Kristin Bergum
GSGeorge E. Stan
George E. Stan
ILIn-Hwan Lee
In-Hwan Lee
AKAndrej Kuznetsov
Andrej Kuznetsov