Jishnu J. Bhattacharyya

Jishnu J. Bhattacharyya

Auto-generated profile, based on publicly available information

Jishnu J. Bhattacharyya

Department of Materials Science and Engineering, University of Virginia, Charlottesville, USA

Research Focus & Metrics

Academic Career Length

10Years (2017-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
29 September 2023 in Additive Manufacturing
Verified
Journal Article
Closed access
LGLin Gao
Lin Gao
JBJishnu Bhattacharyya
Jishnu Bhattacharyya
WLWenhao Lin
Wenhao Lin
ZRZhongshu Ren
Zhongshu Ren
ACAndrew C. Chuang
Andrew C. Chuang
TSTao Sun
Tao Sun

13 March 2023 in Materials Science and Engineering: A
Verified
Journal Article
Closed access
SAS.R. Agnew
S.R. Agnew
NPN.E. Peterson
N.E. Peterson
JBJ.J. Bhattacharyya
J.J. Bhattacharyya
HMH. Macdonald
H. Macdonald
MWM.A. Wischhusen
M.A. Wischhusen
MWM. Webster
M. Webster

22 July 2024 in High Entropy Alloys & Materials
Verified
Journal Article
Open access
PDF file
JBJishnu J. Bhattacharyya
Jishnu J. Bhattacharyya
SASean R. Agnew
Sean R. Agnew
This work addresses the question, “Which microstructure yields the highest “toughness” for a two phase, compositionally complex alloy (CCA) composed of a ductile, face centered cubic (FCC) matrix phase and a stronger, intermetallic reinforcing phase?” A polycrystal plasticity model is used, which takes as input the phase fraction, grain sizes, and parameters describing the mechanical properties (stiffness, strength and strain hardening behavior) of each phase. In addition to assuming an elasto-viscoplastic matrix, the reinforcing phase is also assumed to be elasto-viscoplastic, albeit with a higher strength and lower strain hardening rate. The results reveal that, if the reinforcement remains elastic, the addition of such a reinforcement leads to an increase in strain hardening rate, in addition to the obvious increase in yield strength. If the reinforcement yields, the hardening rate sharply decreases, leading to earlier tensile instability. Therefore, when the strength contrast between the phases is high, addition of reinforcement is beneficial to toughness as well as strength. For lower contrast cases, the optimal toughness case may be the unreinforced matrix material. More specifically, only if the FCC matrix exhibits sustained linear hardening-type behavior typical of TWIP or TRIP effects (which correlate with very low stacking fault energies achievable in CCAs), will it exhibit an increase in toughness, as well as an increase in strength. Finally, the hard reinforcement is under a lower stress triaxiality due to pressure imposed by the ductile matrix, and this causes it to yield at a lower uniaxial stress than it would in isolation. The findings of this work provide a mechanistic understanding of the dependence of toughness on the microstructure of two-phase aggregates, and the approach is equally applicable to multiphase alloys.

1 March 2024 in High Entropy Alloys & Materials
Verified
Journal Article
Open access
PDF file
JBJishnu J. Bhattacharyya
Jishnu J. Bhattacharyya
MWMark A. Wischhusen
Mark A. Wischhusen
SASean R. Agnew
Sean R. Agnew
Achieving high strength, ductility, and toughness via microstructure design is challenging due to the interrelated dependencies of strength and ductility on microstructural variables. As a natural extension of the microstructure design work in Bhattacharyya and Agnew (Microstructure design of multiphase compositionally complex alloys I: effects of strength contrast and strain hardening, 2024), an optimization framework to obtain the microstructure that maximizes the toughness is described. The strategy integrates a physics-based crystal plasticity model, which accounts for damage evolution within the reinforcement through a “vanishing cracked particle” model that is governed by Weibull statistics, and a genetic algorithm-based optimization routine. Optimization constraints are imposed in the form of bounds on the microstructure parameters such that they are most likely attainable by conventional thermomechanical processing. Various matrix strain hardening behaviors are considered, as well as the strength contrast between the two phases and fracture behavior of the reinforcement. It is shown that the addition of a fine-grained (hard) reinforcing phase is preferred as is a matrix that exhibits sustained strain hardening such as is observed under TRIP/TWIP scenarios. Finally, the Pareto-optimal set of solutions for several scenarios are presented which offer new insights into the linkages between microstructure and mechanical properties.

2 January 2019 in JOM
Verified
Journal Article
Closed access
PDF file
VBVikaas Bajikar
Vikaas Bajikar
JBJishnu J. Bhattacharyya
Jishnu J. Bhattacharyya
NPNathan Peterson
Nathan Peterson
SASean R. Agnew
Sean R. Agnew

18 September 2026 in High Temperature Corrosion of Materials
Verified
Journal Article
Open access
PDF file
JBJishnu J. Bhattacharyya
Jishnu J. Bhattacharyya
YRYunjo Ro
Yunjo Ro
SASean R. Agnew
Sean R. Agnew
HWHaydn N. G. Wadley
Haydn N. G. Wadley
Motivated by emerging interests in high temperature multimaterial topology optimized blisk structures, accelerated characterization of the oxidation behavior of composites comprised of consolidated near-α Ti alloy Ti6242S and γ-TiAl-based Ti4822 powders is investigated. Oxidation tests of seven compositions (0, 10, 25, 50, 75, 90, and 100 wt% Ti4822) were carried out in air between the upper use temperature of 600 °C and a higher temperature of 850 °C intended to accelerate the rate of oxidation. After oxidation for 24–50 h, monolithic Ti6242S showed significant mass gain during oxidation at (and beyond) 600 °C while Ti4822 required exposure at 750 °C and above to define the oxidation kinetics. The experimental oxidation behavior of both the terminal compositions and composites was adequately modelled by the parabolic oxidation model. Interestingly, the data reveal a similar temperature dependence (i.e. activation energy) for all composites investigated. The mass gain data of the composites reveal that the oxidation resistance, as indicated by the logarithm of the parabolic rate constant, increases linearly with the addition of Ti4822. This correlated with previously published observations that the oxidation of many Ti alloys scales linearly with the Al content in the alloy and with the fact that the reaction layer between the Ti6242S and the Ti4822 particle domains is rich in α 2 Ti 3 Al phase, which has an oxidation behavior intermediate to that of the “pure” alloys. Based on these experimental data, a “go, no-go” constraint was developed for preliminary design using topology optimization algorithms to select candidate materials for hot, oxygen-exposed surface regions of multi-material structures.