Yuntao Xu

Yuntao Xu

Auto-generated profile, based on publicly available information

Yuntao Xu

Naval Postgraduate School, Monterey, CA, USA

Research Focus & Metrics

Academic Career Length

5Years (2022-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
9 February 2022 in IEEE Transactions on Power Electronics
Verified
Journal Article
Closed access
LRLakshmi Ravi
Lakshmi Ravi
DZDi Zhang
Di Zhang
DQDehao Qin
Dehao Qin
ZZZheyu Zhang
Zheyu Zhang
YXYuntao Xu
Yuntao Xu
DDDong Dong
Dong Dong
Traditional metal oxide varistor (MOV) based voltage clamping circuits (VCC) used in solid-state circuit breakers reduce the efficiency of the system due to the high voltage requirement imposed on the main solid-state device. The voltage burden arises from the material properties of the MOV which fixes its clamping voltage at a value more than twice its maximum continuous dc voltage rating. This letter proposes a novel and reliable VCC termed as the electronic MOV (eMOV) to altogether decouple the peak clamping voltage of the MOV from the nominal dc voltage of the system aiming to improve the voltage suppression index (VSI = Vpk / V dc ) of the VCC, thereby reducing the system conduction losses. The eMOV introduces a breakover diode to share the system dc voltage during the standby state and a Silicon controlled rectifier to provide the bypass path for the fault current for quick MOV insertion. Comprehensive design criteria are developed to guide the component selection and overall design. Experimental results at 2 kV dc and 1.1 kA peak current are presented to validate the operation of the proposed eMOV based VCC.

20 April 2023 in IEEE Transactions on Industry Applications
Verified
Journal Article
Closed access
DZDi Zhang
Di Zhang
YXYuntao Xu
Yuntao Xu
JBJonathan Brandt
Jonathan Brandt
ZZZheyu Zhang
Zheyu Zhang
DQDehao Qin
Dehao Qin
DDDong Dong
Dong Dong
This paper presents a high-density, high-efficiency megawatt (MW) medium-voltage (MV) solid-state circuit breaker (SSCB) for aviation hybrid electric propulsion applications. The proposed SSCB is based on the mature silicon (Si) insulated gate bipolar transistor (IGBT) devices. With reduced IGBT gate voltage, the proposed SSCB can limit the peak fault current without the fault current limiting inductor. Thus, the specific power density of the SSCB is substantially improved compared with the traditional design. This method has negligible impact on SSCB efficiency, reliability and energy absorbed by the metal-oxide varistor (MOV), while providing additional mechanical layout freedom for power density and insulation enhancement. The potential design challenges due to the extremely high ramp rate of the system fault current and the corresponding solutions are also discussed. The performance of the proposed SSCB is validated with experimental results.

11 September 2023 in IEEE Transactions on Industry Applications
Verified
Journal Article
Closed access
DQDehao Qin
Dehao Qin
ZZZheyu Zhang
Zheyu Zhang
DZDi Zhang
Di Zhang
YXYuntao Xu
Yuntao Xu
CWCheng Wan
Cheng Wan
YCYang Cao
Yang Cao
Power semiconductors need to momentarily operate in the active area of DC solid-state circuit breakers (DC-SSCB) to limit the fault current. During this interval, a severe voltage oscillation is observed, leading to the DC-SSCB overstress and eventually failure. This paper aims to understand the mechanism causing the voltage oscillation and devise solutions to suppress it. First, a MATLAB/Simulink model is built with comprehensive considerations of power semiconductors, parasitics, gate drive, and metal oxide varistor (MOV). Then a sensitivity study is performed to identify the critical impact factor(s) causing the voltage oscillation. Afterward, three suppression methods using enhanced gate drive circuitry are proposed and compared. Finally, test results based on a 2kV/1kA SSCB prototype demonstrate the accuracy of the derived model and the effectiveness of the proposed oscillation mitigation methods.