This paper presents a series of test results of large-scale rectangular concrete-filled steel tubular (CFST) beams to explore their performance under pure bending. Concrete-filling tests were initially carried out on two beam specimens of 12-m in length to investigate the feasibility of casting horizontally large-scale rectangular tubes. A total of six 6-m long specimens were subjected to flexural test afterward, including four CFST beams and two steel hollow section (SHS) beams for comparison. The test results showed that the rectangular CFST beams behaved in a relatively ductile manner. The concrete infilling enhanced the flexural behavior and performance of the steel tubes. Finally, the rigid-plastic theory showed suitable to predict the moment capacity of CFST compact beams.
1 October 2018 in Revista IBRACON de Estruturas e Materiais
This paper presents an experimental study with numerical modeling of Crestbond shear connectors in concrete filled tube columns. The Crestbond, which consists in a steel plate with regular cuttings, was originally conceived for composite beams and is now being proposed as an alternative device for load introduction and shear transfer at the steel-concrete interface in concrete filled tube columns. The results achieved in this work were very favorable to the new application proposed for the connector as high values of shear strength were obtained. Moreover, the numerical and experimental results enabled comparative analysis and investigations regarding the influence of concrete conditions and the geometry of the column section on the mechanical properties of the connector.
1 June 2019 in Revista IBRACON de Estruturas e Materiais
In search of an improved compatibility between cold-formed steel profiles and precast floor systems, this study proposes an alternative shear connector for cold-formed steel-concrete composite beams. This connector consists of a steel plate with holes placed longitudinally in the middle of the upper flange of the steel profile, aiming to maximize the support area for precast slabs during the assembly. The proposed solution was experimentally tested on I-beams under bending, composed by two cold-formed steel channels, connected to a reinforced concrete slab by the shear connector. The relative slip between the steel profile and concrete, vertical deflection of the beam, and strains at several locations of the composite section were measured. The results show that the proposed connector assures shear transfer at the interface of the composite section components and shows strength of the same magnitude as other commonly used connectors.
É descrito o comportamento da estrutura de perfis formados a frio (PFF) submetida ao incêndio ocorrido em um apartamento de um conjunto habitacional de baixo custo, com quatro blocos idênticos de quatro pavimentos e oito apartamentos por andar. Cada apartamento tem 44 m² de área total. Segundo a Norma Brasileira, esse tipo de edifício é isento de verificação estrutural em situação de incêndio. Foram realizados ensaios para a caracterização do aço empregado nos pilares e vigas e ensaios metalográficos para estimar a temperatura atingida pelo aço durante o incêndio. O modelamento CFD (Computational Fluid Dynamics) do cenário do incêndio foi feito utilizando-se o programa de computador SMARTFIRE. A análise térmica da estrutura de aço em situação de incêndio foi realizada por meio do programa SUPERTEMPCALC. A verificação estrutural foi feita empregando-se as expressões da Norma Brasileira para o projeto dos PFF em temperatura ambiente, com base no AISI/USA, mas usando os fatores de redução de resistência recomendados pelo Eurocode 3 part1.2.
A shear connector, developed to be applied to a composite beam whose steel profile is a thin-walled box profile, displayed much greater flexibility than the conventional welded shear connector, leading to particular issues in the composite beam behaviour. One of these issues is the role played by friction at the interface between the steel profile and the slab which, under particular circumstances, may be relevant for serviceability limit states and also for ultimate limit states. The Brazilian and American Standards do not yet recognize the friction contribution in the behaviour of composite beams, though they recognize this contribution in composite slabs. This paper presents the experimental tests carried out with and without friction contribution on simple supported composite beams with flexible connectors and the numerical models developed to simulate the behaviour of the tested beams. The experimental tests revealed significant increases in strength and stiffness of the composite beam due to friction contribution and the comparisons between numerical and experimental results displayed good correlations.
Resumo Este trabalho apresenta uma análise da influência do tipo de combate a incêndio nas temperaturas desenvolvidas em um compartimento utilizado pelo Corpo de Bombeiros Militar de Minas Gerais (CBMMG) em seus treinamentos. Os tipos de combate variaram com o modo de aplicação de água em pulsos simples, dois pulsos ou pulsos mais longos. Os resultados demonstraram que os treinamentos representam bem os incêndios reais em ambientes construídos com as fases de início do incêndio e sua propagação, inflamação generalizada (flashover) e pós-flashover. Observou-se que a taxa de aplicação de água influencia inversamente no tempo de duração do incêndio e na temperatura da região onde os combatentes se localizam. Foram realizados também ensaios sem intervenção e constatou-se que não há uma diferença significativa nas temperaturas máximas atingidas em comparação com os treinamentos normais. Os ensaios realizados no compartimento também demonstraram que ele pode ser utilizado para estudo de elementos construtivos e estruturais em situação de incêndio.