Os aços inoxidáveis austeno-ferríticos apresentam estrutura ferrítica e austenítica com inter-metálicos dispersos na matriz. Tais precipitados, responsáveis pelas propriedades mecânicas do material, dependem da composição química e do processo de fabricação. A identificação desses intermetálicos pode ser feita com o software FactSage, sistema computacional integrado com acesso às informações termodinâmicas das soluções. O FactSage pode estimar as quantidades das fases complexas dos aços inoxidáveis austeno-ferríticos e, em particular, a precipitação da fase sigma e de Laves, considerando as condições de equilíbrio termodinâmico. No entanto, os resultados das simulações podem ser diferentes aos dos procedimentos experimentais, pois as microestruturas desses aços variam, conforme as diferentes condições de tratamento térmico. Nesse artigo, o objetivo foi comparar os resultados da simulação com os do procedimento experimental. Embora a simulação indique a formação da fase sigma e de Laves nos dois tratamentos térmicos, solubilizado e solubilizado mais envelhecido, a análise microestrutural revela apenas a fase sigma, na segunda condição. Palavras-chave:Software FactSage. Aço inoxidável austeno-ferrítico. Fase de Laves e sigma
In austenitic-ferritic or duplex stainless steels, the microstructure is basically determined by the chromium and nickel contents, which are ferritic or austenitic phases stabilizers. Currently, duplex stainless steels are used to replace austenitic stainless steels in industrial applications, where requirements for corrosion resistance and mechanical strength are greater. In these steels, solidification starts at about 1450 oC with the formation of ferrite (α), which gives origin to austenite (γ) near 1300 oC. The σ phase nucleates preferentially in austenite/ferrite interface incoherent with the matrix in the range of 600 to 950 oC and compromises the cast steels toughness. Laves phase (Fe2Nb) is favored in stainless steels containing niobium. In this context, the objective of this research was to evaluate the effect of niobium on the formation of sigma and Laves phase in conventional austenitic-ferritic stainless steel and modified with 0.2, 0.5 and 1.5% niobium. The steels were heated at 1050 ºC for one hour and subsequently at 650 °C too, with cooling in water. The chemical compositions of sigma and Laves were determined semi-quantitative by energy dispersive X-rays (EDS). The amounts of Laves and sigma were obtained by computational thermodynamic simulation with the FactSage software. The results show that the thermodynamic simulation predicts Laves in the four steels, although in conventional stainless steel the microstructure is free from this phase. Regarding microstructural analyses by SEM, it is possible to observe the sigma phase in all steels, only after aging, while Laves appears in those modified with niobium in both heat treatment conditions. Whit regard to niobium, it favors the formation of sigma and Laves phase, however, the thermodynamic simulation results are different from the experimental ones.
1 January 2026 in Advances in Materials Science and Engineering
Sulfur pick‐up in steel during converter operations, caused by the addition of certain raw materials, requires subsequent desulfurization in the ladle to achieve sulfur levels below 0.0050%. This study employs computational thermodynamics to evaluate the properties of slags formed after steel tapping and their relationship with desulfurization efficiency. Steel and slag samples were collected from industrial heats at the ArcelorMittal Tubarão steel plant after 5 minutes of ladle treatment. The chemical composition of the steel was analyzed to determine sulfur content and process efficiency. Slag composition was used to calculate key properties, including CaO content, phase fractions, Al 2 O 3 , SiO 2 , and viscosity, using Thermocalc and FactSage software. Correlations between these properties and desulfurization efficiency were established. The results indicate that optimal desulfurization is achieved with slags containing adequate solid CaO while maintaining liquid phase saturation. CaO activity (aCaO) was identified as the most influential parameter. Based on these findings, a new steel desulfurization factor is proposed to estimate process efficiency. Additionally, multivariate regression analysis demonstrated that aCaO has the greatest impact on desulfurization efficiency, particularly in slags not saturated with CaO.