Ki-O Kim

Ki-O Kim

Auto-generated profile, based on publicly available information

Ki-O Kim

Department of Automotive Engineering, Hanyang University, Seoul, Republic of Korea

Research Focus & Metrics

Academic Career Length

4Years (2023-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
19 June 2023 in IEEE Transactions on Magnetics
Verified
Journal Article
Closed access
KKKi-O Kim
Ki-O Kim
YJYoung-Hoon Jung
Young-Hoon Jung
JPJin-Cheol Park
Jin-Cheol Park
Myungseop LimMyungseop Lim
Myungseop Lim
In this article, the electrical and mechanical characteristics of multilayer interior permanent magnet synchronous motors (ML-IPMSMs) using ferrite permanent magnets (PMs) are compared when driven at high speeds with respect to the type of electrical steel. In high-speed operation, the mechanical and electrical characteristics of ML-IPMSMs vary depending on the number of PM layers, PM shape, number of bridges, and bridge thickness. Additionally, ferrite PMs have a lower coercive force than neodymium (Nd) PMs; therefore, irreversible demagnetization (ID) must be considered, and it is affected by the number of PM layers and PM shape of ML-IPMSMs. Thus, when designing a multilayer IPMSM using ferrite PMs for electric vehicle (EV) traction, all characteristics should be considered. Compared to conventional electrical steel (CES), high-strength electrical steel (HSES) offers advantages in mechanical properties, allowing for greater flexibility in ML shape. Consequently, it is possible to design a shape with improved electrical performance when compared to CES by adjusting the ML shape. In this article, all characteristics of each ML-IPMSM using HSES and CES are reviewed via finite element analysis (FEA), and the benefits of HSES applied motors for high-speed driving motors are presented. To verify the validity of the review content in this article, experiments are conducted on the manufactured motor, and FEA results are compared with the test results.

10 July 2023 in IEEE Transactions on Magnetics
Verified
Journal Article
Closed access
JPJin-Cheol Park
Jin-Cheol Park
JKJae-Hyun Kim
Jae-Hyun Kim
SPSoo-Hwan Park
Soo-Hwan Park
KKKi-O Kim
Ki-O Kim
MSMoo-Hyun Sung
Moo-Hyun Sung
Myungseop LimMyungseop Lim
Myungseop Lim
In the interior permanent magnet synchronous motor (IPMSM), an asymmetric rotor is used as a design method to reduce torque ripple or cogging torque by adjusting the saturation of the rotor core. The advantage of an asymmetric rotor is that it can reduce torque ripple or cogging torque in the forward direction while maintaining the average torque or output power. However, when driving in the reverse direction, the torque ripple or cogging torque can be increased. Therefore, the asymmetric rotor produces different characteristics in the forward and reverse directions. In this study, the asymmetric rotor shape is designed using an optimization technique taking into consideration the rotating direction. The optimum design is performed based on the symmetric rotor as the base model. When rotating in the forward direction, the asymmetric rotor has a lower torque ripple than the symmetric rotor, and when rotating in the reverse direction, the asymmetric and symmetric rotors are designed to be similar. The kriging surrogate model was used to determine the optimum design point that satisfied the constraints. Finally, a symmetric and asymmetric rotor was manufactured and evaluated through tests.

14 August 2023 in IEEE Transactions on Magnetics
Verified
Journal Article
Closed access
SPSoo-Hwan Park
Soo-Hwan Park
KKKi-O Kim
Ki-O Kim
Myungseop LimMyungseop Lim
Myungseop Lim
As the demand for increasing the efficiency of traction motor for increasing the mileage of electric vehicles, it is necessary to accurately estimate the efficiency of traction motor at the early design stage. Since the iron loss of the traction motor is highly affected by the pulse width modulation (PWM) frequency, the PWM current should be considered when designing the motor. However, it is difficult in considering the PWM current at early design stage because of its high computation cost due to the small time step for representing the high frequency harmonics. Therefore, we propose a method to reduce the computation cost for the calculation of PWM-induced iron loss using deep transfer learning even with small amount of data. The proposed method can be achieved by training a deep neural network that can predict PWM-induced iron loss accurately using a large amount of sinusoidal current-based iron loss and a small amount of PWM-induced iron loss. As a result, the PWM current can be practically considered in design stage of traction motor because the computation cost can be decreased by using the proposed method.

9 August 2023 in IEEE Transactions on Magnetics
Verified
Journal Article
Closed access
YJYoung-Hoon Jung
Young-Hoon Jung
KKKi-O Kim
Ki-O Kim
Myungseop LimMyungseop Lim
Myungseop Lim
This paper proposes the performance improvement of the rare-earth free high-speed multilayer (ML) IPMSM by using the dual-phase magnetic material (DPMM). To ensure mechanical stability, ML IPMSM should have many bridges. However, in the bridges, a significant leakage flux generates, and, due to this, the performance of the motor is decreased. Since the DPMM has magnetic and non-magnetic phases, to solve this problem, the non-magnetic phase is applied to the bridges of ML IPMSM. Through it, the leakage flux is decreased, and performance improvement of the motor is achieved. In this paper, the electrical parameters, torque, and efficiency are compared using finite element analysis for the motor with and without the DPMM. Finally, to verify the proposed method, the load test is conducted.

21 May 2024 in IEEE Transactions on Magnetics
Verified
Journal Article
Closed access
KKKi-O Kim
Ki-O Kim
DPDu-Ha Park
Du-Ha Park
SISo-Yeon Im
So-Yeon Im
YCYunyong Choi
Yunyong Choi
Myungseop LimMyungseop Lim
Myungseop Lim
In this article, the interior permanent magnet synchronous motor (IPMSM) using ferrite permanent magnet (PM) for micro-electric vehicle (EV) traction is proposed. The characteristics of V-type IPMSM using Nd PM and a motor of the same shape using ferrite PM are analyzed when applied to micro-EV traction, the cases of power dissatisfaction with ferrite PM motor are derived, and the improvement methods are presented. Based on the improvement method, the rotor outer diameter, PM layer, and PM ratio are considered in the initial design. After the initial design, a two-stage optimization method is introduced to reduce the number of samples required. The first optimization is performed considering the power of the driving area, mechanical stiffness analysis during high-speed rotation, and low-temperature demagnetization analysis of ferrite PM. Then, the second optimization is performed considering the main operating points (MOPs) of the efficiency perspective and the MOPs of the frequency perspective through micro-EV model. Based on the design results, the possibility of a motor for micro-EV using ferrite PM is suggested by comparing the performance with the existing motor using Nd PM. Experiments are conducted on the manufactured motor, and the validity of the design results is verified by comparing the test results and FEA results.

1 October 2025 in IEEE Transactions on Magnetics
Verified
Journal Article
Closed access
YHYounjae Hwang
Younjae Hwang
KKKi-O Kim
Ki-O Kim
WCWon-Seok Cha
Won-Seok Cha
BBByeong-Cheol Bae
Byeong-Cheol Bae
JKJae-Hyeon Kim
Jae-Hyeon Kim
Myungseop LimMyungseop Lim
Myungseop Lim
Axial flux permanent magnet (AFPM) motors have drawn significant attention due to their compact size, high torque density, and broad applicability. However, accurately designing an AFPM motor requires computationally intensive three-dimensional finite element analysis (3D FEA) owing to its topology. To alleviate this, a quasi-three-dimensional (quasi-3D) model can be employed, in which the AFPM motor’s geometry is divided in the radial direction and represented in a flattened, two-dimensional equivalent form. The quasi-3D model offers an efficient alternative, but it typically fails to consider important factors, such as radial flux leakage. This limitation can result in discrepancies between the predicted voltage and torque and those obtained from 3D FEA results. In this article, we improve the conventional quasi-3D model by calculating the radial leakage path’s permeance and incorporating it into the two-dimensional analysis. As a result, the improved quasi-3D model exhibits a better correlation with 3D FEA than the conventional quasi-3D model with a higher division. The improved quasi-3D model significantly reduces computational cost with minimal sacrifice of precision compared to 3D FEA, enabling faster and more reliable design processes.