22 December 2020 in Smart Materials and Structures
We present hybrid electrostatic and gecko-inspired gripping pads that help robots to lift and carry bulky objects. The directional, gecko-inspired adhesive provides a controllable shear force with low normal force, providing a very high effective coefficient of friction so that items like bags full of groceries and heavy cardboard boxes can be lifted using only 1–2 N of squeezing force. The addition of electrostatics helps the pads to conform to non-smooth surfaces, providing substantially higher shear forces than with gecko-inspired adhesives alone. The electrostatic effect is enhanced by doping the silicone rubber adhesive material with calcium copper titanate (CCTO), except at the contacting faces of the adhesive microstructures, where a smooth surface finish is important for adhesion. We describe the multimaterial fabrication process used to create the new hybrid adhesive and present the results of robotic lifting experiments with non-smooth bulky items.
13 January 2021 in Journal of The Royal Society Interface
Materials are traditionally tested either by imposing controlled displacements and measuring the corresponding forces, or by imposing controlled forces. The first of these approaches is more common because it is straightforward to control the displacements of a stiff apparatus and, if the material suddenly fails, little energy is released. However, when testing gecko-inspired adhesives, an applied force paradigm is closer to how the adhesives are loaded in practice. Moreover, we demonstrate that the controlled displacement paradigm can lead to artefacts in the assumed behaviour unless the imposed loading trajectory precisely matches the deflections that would occur in applications. We present the design of a controlled-force system and protocol for testing directional gecko-inspired adhesives and show that results obtained with it are in some cases substantially different from those with controlled-displacement testing. An advantage of the controlled-force testing approach is that it allows accurate generation of adhesive limit curves without prior knowledge of the expected behaviour of the material or the loading details associated with practical applications.
5 April 2023 in Advanced Materials Technologies
10 March 2022 in IEEE Robotics and Automation Letters
We present hybrid adhesive end-effectors for bimanual handling of deformable objects. The gripping system is driven by the need to achieve alignment on deformable and irregular surfaces while maintaining a large area of contact for efficient use of the adhesive. The objective of the gripping system is to reduce the internal grasping force needed to securely lift and manipulate objects with two arms, for example, in warehousing and retail environments. The end-effectors are designed with features meant to accommodate surface irregularities in macroscale form, mesoscale waviness, and microscale roughness, achieving good shear adhesion on surfaces with little gripping force. The new gripping system combines passive mechanical compliance with a hybrid electrostatic-adhesive pad so that humanoid robots can grasp a wide range of materials including paperboard and textured plastics with internal grasping forces of 1 N and 0.5 N, respectively. These grasping forces are more than 10 times smaller than without the hybrid pad. As an application, we demonstrate a humanoid robot handling delicate deformable objects ranging from flowers in a plastic sleeve to a 2.4 kg sack of rice with less than 1.5 N of normal gripping force.
1 August 2023 in IEEE Robotics and Automation Letters
We present a solution to the separate challenges faced by suction cups and gecko adhesives for one-sided grasping of heavy, irregular items. The gripping technology combines suction with adhesion for grasping and placing a wide range of objects in packed spaces. Applications include shopping and restocking in retail and warehouse settings where products vary in size and weight and are packed tightly, which limits access. A single suction cup is compact enough to reach and grasp the smallest items (down to 5 cm in size) but cannot provide the shear force needed for handling bulky items. Gecko-inspired adhesion provides extra lifting capability for objects up to 2.3 kg, using a 7.6 x 12.7 cm adhesive swatch – 2.5x heavier than with suction alone. The adhesive is fabricated on a flexible nylon fabric. A small fan blows gently to help the fabric conform to irregular surfaces prior to lifting.
1 June 2021 in Journal of Micro and Nano-Manufacturing
Fabrication techniques for gecko-inspired adhesives generally target mold durability, adhesive performance, and process efficiency and simplicity. With these goals in mind, we present a micromachining process for creating reusable aluminum molds used to fabricate directional dry adhesives. The molds require deep, narrow and overhanging grooves to create sharp and angled adhesive features. This geometry precludes most traditional machining and lithographic material removal processes. The presented process is a hybrid of indenting and orthogonal machining, using a diamond-coated microtome blade as the tool. An finite element analysis reveals the local extent of work hardening as each groove is created, and helps to define a trajectory that reduces the effects of tool deflection and chip build up. The results of a series of experiments agree with predictions from the analysis and reveal a range of blade approach angles and a lower bound on groove spacing to achieve the desired geometry. This range is narrower than for molds machined from wax in previous work. Nonetheless, adhesive samples cast from the new metal molds achieve comparable performance to those previously cast from wax.