Compressing the surface of sawn timber results in a substantial increase in hardness, and this opens up new market opportunities of using low-density timber species as the raw material for high-value wood products. Unfortunately, widespread commercialisation is hindered by the lack of an industrially viable surface densification process, the major obstacle being the set-recovery (SR) of the densified wood cells upon exposure to moisture. Our hypothesis is that partial dissolution of the crystalline cellulose during densification will largely prevent the SR of densified wood. We therefore evaluated the effect of ionic liquid (IL) or organic superbase pre-treatment on the elastic spring-back (SB), SR and Brinell hardness (HB) of surface-densified wood. Specimens of Scots pine were treated with solutions of ILs or superbases, and then densified in a hot press at temperatures between 200°C and 270°C. The SR was reduced from 90% for the control group to only about 10% for the treated materials. The treated and densified specimens exhibited a higher HB than their untreated and densified counterparts. The method presented in this study is a precursor to the development of a continuous densification process adapted for an open system. Further studies are needed to understand the underlying mechanisms of the pre-treatment.
31 October 2017 in iForest - Biogeosciences and Forestry
The hardness of the outer regions of solid wood can be improved by surface densification, and this opens up new fields of application for low-density species. So far, surface densification relies on time- and energy-consuming batch processes, and this means that the potential advantages over more expensive hardwood species or non-renewable materials are reduced. Using fossil-based plastics or applying wood densification processes with a high energy consumption has adverse effects on the environment. In a previous study, it was shown that the surface of wood can be densified by a continuous high-speed process, adopting a roller pressing approach. The desired density profiles could be obtained at process speeds of up to 80 m min-1, but an equally simple and fast method to eliminate the moisture-induced set-recovery of the densified wood cells is still required. For this reason, the goal of the present study was to evaluate the effect on the set-recovery and hardness of surface-densified Scots pine after a fast pre-treatment with solutions of sodium silicate, sodium hydroxide, methacrylate resin, and ionic liquids. The Scots pine specimens were pre-treated by applying the chemical treatment and impregnation agents to the wood surface with a paper towel, before the specimens were densified. For each type of treatment, 15 specimens were densified in a hot press. The set-recovery was measured after two wet-dry cycles, and 30 Brinell hardness measurements were carried out on each group of specimens. In general, the effect of the treatments on the set-recovery was rather low. Ionic liquid solutions appear to work as a strong plasticiser and the treatment led to a reduction in set-recovery by 25%. The treatments with sodium silicate, ionic liquids and methacrylate resin led to a greater hardness than in untreated and densified specimens. Further experiments are needed to improve the depth of penetration of the treatment solutions into the wood surface, as this was identified as one of the main causes of the rather weak effects.
The established methods for testing the hardness of wood are of questionable value for assessing the performance of surface-densified wood, since the density profile beneath the densified surface is an important property that needs to be considered. The purpose of this study was to evaluate the influence of the density profile of surface-densified wood and the hardness test parameters, such as indenter geometry and applied load on the measured hardness. The influence of the density profile varied considerably depending on the hardness test parameters. This can make a comparison of hardness values of surface-densified wood prone to misinterpretation. The selection of hardness test parameters should either be product-specific, or the density profile itself should be used to evaluate the hardness of surface-densified wood. A strong influence of the density profile on the indentation depth development during the hardness tests indicates the possibility of predicting the density profile based on the hardness test methods.
Wood under thermo-mechanical densification behaves differently depending on the cross-sectional growth ring orientation (GRO) relative to the direction of compression. This influences the degree of cell damage, but also the shape-memory effects occurring when the compression load is released (spring-back) and when the timber is re-moistened (set-recovery). To study how the GRO influences the shape-memory effects, Scots pine specimens were separated into three distinct groups of GRO (Flat, Inclined, Hybrid) and then thermo-mechanically surface-densified. Spring-back and set-recovery were determined by thickness measurements and by digital image correlation. A GRO parallel to the densified surface, resulted in a low spring-back and a high set-recovery which were uniform over the width of the specimen. Specimens with a GRO between 15 and 45° to the densified surface showed high spring-back and low set-recovery, indicating cell-wall damage. Spring-back mainly occurred in the non-plasticised region immediately below the heated surface region and elasto-plastic rolling-shear deformation along individual growth rings occurred. The GRO of softwood subjected to thermo-mechanical densification determines if an applied load results in rolling shear-deformation or radial compression. This in turn determines where in the cross-section and when in the process the cells deform and if this deformation occurs below or above the glass-transition temperature.
The moisture-induced recovery of compressed wood is one of the major problems of wood densification technology. Achieving a cost-efficient surface densification process without the need for additional resins to eliminate the set-recovery may lead to an increase in value of low-density wood species. A previous study has shown that a pre-treatment with ionic liquids (ILs) can nearly eliminate the set-recovery. It was however observed that during the pre-treatment process the IL did not penetrate sufficiently deep into the wood to explain the achieved reduction in set-recovery. Based on these findings, the hypothesis was posed that further penetration of the IL into the wood occurs during the densification stage as a consequence of the applied heat and pressure. Thermo-gravimetric analysis (TGA) and gas-chromatography mass-selective-detection (GC-MSD) showed that the depth of penetration of the IL was greater after the densification process than before. Digital image correlation (DIC) showed that in regions with a high IL concentration, there was almost no set-recovery, and it gradually increased with a decrease in the IL concentration, as observed with TGA and GC-MSD analysis.
4 June 2022 in European Journal of Wood and Wood Products
Over the past decades, the surface densification of solid wood has received increased attention. However, the inhomogeneous density distribution in the densification direction might be a challenge with regard to process control within a large-scale production process, as the density profile governs many relevant properties of surface-densified wood. Currently, the measurement of density profiles relies on sensitive X-ray equipment and is difficult to integrate into an on-line process. Hence, in this study, three machine learning approaches were applied to predict the density profiles of surface-densified Scots pine specimens, only based on visual image acquisition—a technology that is ubiquitous in the wood industry: partial least squares (PLS) regression, artificial neural networks (ANN), and convolutional neural networks (CNN). The machine learning models were trained on images of the specimen cross-sections as input data, and X-ray density profiles as output data. There were 1850 observations, and the model performance was evaluated on external test sets. The models had mean absolute percentage errors of the predicted values between 9 and 18%; the CNN achieving the smallest error (9.24%). A deeper analysis of the data revealed that the ANN approach performed inconsistently between observations. PLS regression predicted the main density peak to a high accuracy but could not model other features. Only the CNN could reliably model the main density peak, wide growth rings, and the important region between the specimen surface and the main density peak. The ability of the models to generalise to untypical new data was improved by augmentation of the training data.