6 December 2025 in Nature Communications
Inorganic electrolytes dominate all-solid-state batteries (ASSBs), but face critical limitations, including interfacial instability, complex manufacturing, and challenges in operating under commercially viable conditions. Here, we present a transformative approach using zwitterionic dry polymer electrolytes (ZPEs) designed via a conflicting entropy strategy to enable scalable energy-dense ASSBs. Guided by Flory–Huggins theory, liquid-state zwitterionic monomers exhibit higher mixing entropy with Li salts compared to conventional long-chain polymers, forming homogeneous monomer/salt mixtures with enhanced intermolecular electrostatic interactions to promote salt dissociation. In situ polymerization of these mixtures yields directionally aligned ion channels decoupled from the polymer backbone, characterized by reduced conformational entropy, allowing rapid Li⁺ migration via an ion-hopping mechanism under ambient conditions. The ZPEs are seamlessly incorporated as a solid catholyte into pre-fabricated high-areal-capacity (10.0 mAh cm⁻²) LiNi0.8Co0.1Mn0.1O2 positive electrodes, ensuring compatibility with existing cell manufacturing processes and has the potential to reduce production complexity and cost. Paired with thin Li-metal negative electrodes (N/P (negative-to-positive electrode capacity) ratio = 1.0), pouch-type ASSB full cells demonstrate a specific energy and energy density of 516 Wh kg−1 and 1329 Wh L−1 (excluding the pouch packaging) and stable cycle life at practical operating conditions (25 °C and 0.5 MPa) in such a constrained cell configuration.
26 May 2023 in Journal of Energy Chemistry
8 November 2022 in Applied Physics Reviews
Although anionic-redox-based layered oxide materials have attracted great attention as promising cathodes for Na-ion batteries because of their high practical capacities, they suffer from undesirable structural degradation, resulting in the poor electrochemical behavior. Moreover, the occurrence of stable anionic-redox reaction without the use of expensive elements such as Li, Co, and Ni is considered one of the most important issues for high-energy and low-cost Na-ion batteries. Herein, using first-principles calculation and various experimental techniques, we investigate the combination of vacancy (□) and Ti4+ cations in the transition-metal sites to enable outstanding anionic-redox-based electrochemical performance in the Na-ion battery system. The presence of vacancies in the P2-type Na0.56[Ti0.1Mn0.76□0.14]O2 structure suppresses the large structural change such as the P2–OP4 phase transition, and Ti4+ cations in the structure result in selectively oxidized oxygen ions with structural stabilization during Na+ deintercalation in the high-voltage region. The high structural stability of P2-type Na0.56[Ti0.1Mn0.76□0.14]O2 enables not only the high specific capacity of 224.92 mAh g−1 at 13 mA g−1 (1C = 264.1 mA g−1) with an average potential of ∼2.62 V (vs Na+/Na) but also excellent cycle performance with a capacity retention of ∼80.38% after 200 cycles at 52 mA g−1 with high coulombic efficiencies above 99%. Although there are some issues such as low Na contents in the as-prepared state, these findings suggest potential strategies to stabilize the anionic-redox reaction and structure in layered-oxide cathodes for high-energy and low-cost Na-ion batteries.
12 November 2024 in ACS Applied Materials & Interfaces
30 July 2023 in Applied Science and Convergence Technology
Eunji Sim, Mihyun Yang, Ha Eun Cho, Somang Koo, Seong Chu Lim, and Kyuwook Ihm. Applied Science and Convergence Technology 2023;32:89-92. https://doi.org/10.5757/ASCT.2023.32.4.89
16 April 2025 in Advanced Materials Interfaces
Area‐selective deposition is a key method for enhancing precision in nanofabrication, particularly for next‐generation semiconductor devices. (N,N‐dimethylamino)trimethylsilane (DMATMS) is attracting increasing attention for its ability to form a selective inhibition layer on technologically important surfaces. However, direct observation of this molecular layer is challenging because of the limited analysis methods available for tracing the monolayer chemistry. This study employs in situ spectroscopy to investigate surface chemistry before and after dry etching, revealing the significant chemical forms influencing the reactivity of DMATMS vapor on both surfaces. Using absorption spectroscopy, the presence of ─OH groups on SiO2 and SiNx are traced. The adsorption reactivity of DMATMS is notably diminished on SiNx due to the exposure of surface NH species after the removal of ─OH groups through dry etching. Conversely, the oxygen‐rich SiO2 surface retains some ─OH groups, leading to no significant change in DMATMS adsorption strength. Tailoring surface ─OH groups through dry etching has minimal impact on SiO2 but significantly suppresses DMATMS adsorption on SiNx, leading to 92.2% selectivity in the subsequently deposited ruthenium (Ru) layer. These results provide a new direction toward increasing area selectivity by directly tracing and controlling the key surface molecules.