Ziad Azar

Ziad Azar

Auto-generated profile, based on publicly available information

Ziad Azar

Sheffield Siemens Gamesa Renewable Energy Research Centre, Sheffield, U.K.

Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
20 October 2020 in IEEE Access
Verified
Journal Article
Open access
DPDileep Kumar Kana Padinharu
Dileep Kumar Kana Padinharu
Guang-Jin LiGuang-Jin Li
Guang-Jin Li
Z. Q. ZhuZ. Q. Zhu
Z. Q. Zhu
RCRichard Clark
Richard Clark
ATArwyn Sean Thomas
Arwyn Sean Thomas
ZAZiad Azar
Ziad Azar
Surface mounted permanent magnet Vernier (SPM-V) machines are known for their high torque density but relatively poor power factor compared to conventional SPM machines. The high torque density feature of the SPM-V machines is desirable for direct-drive offshore wind power applications as it leads to reduced generator size, mass and cost. However, their poor power factor can negatively affect the converter cost and efficiency. This paper compares the system-level performance, including generator active and structural components and converter, between the SPM-V and the conventional SPM generator systems. Four different power ratings, i.e. 0.5MW, 3MW, 5MW and 10MW, have been considered to study the trend of system-level performance with increasing power rating. The study shows that the SPM-V generators can be lighter and cheaper than their conventional SPM counterparts. However, after the consideration of converter cost and efficiency, the conventional SPM generator exhibited slightly better overall performance. Nonetheless, with the development of novel Vernier topologies and reduction in converter costs in the future due to emerging technologies, the Vernier generators can still be competitive for direct-drive offshore wind power applications.

4 March 2024 in IEEE Transactions on Energy Conversion
Verified
Journal Article
Closed access
Z. Q. ZhuZ. Q. Zhu
Z. Q. Zhu
Peng WangPeng Wang
Peng Wang
NFNuno M. A. Freire
Nuno M. A. Freire
ZAZiad Azar
Ziad Azar
XWXimeng Wu
Ximeng Wu
Rotor position estimation error in sensorless controlled surface-mounted permanent magnet synchronous machines (PMSMs) will cause errors in parameter estimation. This paper proposes a novel rotor position-offset injection method for parameter estimation of sensorless controlled PMSMs. During the period of square wave rotor position-offset injection, it is found that the amplitude response of q -axis voltage fluctuation decreases with the increasing accuracy of parameters, and thus, stator inductance and resistance can be estimated by controlling the q -axis voltage fluctuation. The permanent magnet flux linkage is subsequently obtained from the back-EMF observation. Moreover, the guideline is provided for selecting appropriate amplitude and frequency of injected position offset. Compared with conventional methods, the proposed parameter estimation method is immune to rotor position error. The proposed parameter estimation method based on sensorless controlled PMSMs is verified by experiments at different speeds, loads, and temperatures.

26 August 2024 in IEEE Transactions on Transportation Electrification
Verified
Journal Article
Closed access
Dawei LiangDawei Liang
Dawei Liang
Z. Q. ZhuZ. Q. Zhu
Z. Q. Zhu
RNReza Nilifard
Reza Nilifard
ZAZiad Azar
Ziad Azar
NMNima Madani
Nima Madani
JCJens Brix Christensen
Jens Brix Christensen
Lumped-parameter thermal models (LPTMs) have been widely used for thermal analysis and management in various electromagnetic devices and systems, e.g., electrical machines and power electronic modules. However, the existing LPTMs suffer from significant temperature misestimation issues due to assumptions of independent and uniform heat flows and/or concentrated loss generation. Meanwhile, they are also incapable of estimating maximum temperature due to inherent structural limitations. This series of papers proposes the novel LPTMs for cuboidal (Part I) and cylindrical (Part II) components from one to three dimensions to address the above critical issues for the first time. The proposed models are obtained analytically based on the multi-dimensional heat transfer equations, where the interacted heat flow, the distributed loss generation, and the material anisotropy are all considered. Compared to the existing LPTMs, the proposed models exhibit significantly higher estimation accuracy and can simultaneously predict both average and midpoint temperatures. Compared to the finite element analysis (FEA) method, the proposed models can achieve almost identical estimation accuracy while requiring much less computation time. Therefore, they can be used in any applications where LPTMs are required. Finally, both FEA and experiments are used for validation.

11 December 2024 in IEEE Transactions on Transportation Electrification
Verified
Journal Article
Closed access
Dawei LiangDawei Liang
Dawei Liang
Z. Q. ZhuZ. Q. Zhu
Z. Q. Zhu
RNReza Nilifard
Reza Nilifard
ZAZiad Azar
Ziad Azar
NMNima Madani
Nima Madani
High-order lumped-parameter thermal models (LPTMs) can be used to predict spatial temperature distribution and hot spot temperatures for critical components and account for spatial temperature variations in medium-to-large-sized electrical machines. However, all existing high-order LPTMs require overdiscretization levels to reduce estimation errors due to the assumption of concentrated loss generation and/or the inappropriate definition of compensation thermal resistances. Such overdiscretization, however, leads to excessive burdens in thermal modeling and computation. In this article, a novel high-order thermal modeling method is proposed for both cuboidal and hollow cylindrical components, addressing 2-D and 3-D heat transfer problems in electrical machines. The proposed method introduces an individual compensation thermal resistance for each discrete element, which is solely dependent on geometric and thermal parameters and obtained based on the multidimensional heat transfer theorem. As a result, the proposed models can fully consider the distributed loss generation within the component and the thermal continuities between adjacent discrete elements. The proposed models can maintain high estimation accuracy under different discretization levels without increasing computation time. They are further applied to winding regions in a wound lamination core and a permanent magnet synchronous machine (PMSM) for experimental validation.

26 August 2024 in IEEE Transactions on Transportation Electrification
Verified
Journal Article
Closed access
Dawei LiangDawei Liang
Dawei Liang
Z. Q. ZhuZ. Q. Zhu
Z. Q. Zhu
RNReza Nilifard
Reza Nilifard
ZAZiad Azar
Ziad Azar
NMNima Madani
Nima Madani
JCJens Brix Christensen
Jens Brix Christensen
The novel lumped-parameter thermal models (LPTMs) have been developed for a general cuboidal component in Part I. In this paper (Part II), the proposed thermal modelling method is developed for general cylindrical components in all 1-D directions, 2-D planes, and the 3-D solid. By introducing two compensation thermal resistances, both average and midpoint temperatures can be predicted, where the material anisotropy, the distributed loss generation, and the non-uniform heat flow are all considered. Afterwards, together with cuboidal LPTMs in Part I, the proposed LPTMs are further applied to establish a complete thermal network for a permanent magnet synchronous machine, whose prediction results exhibit excellent agreement with both the finite element analyses and experimental results. As will also be shown, the proposed LPTMs demonstrate high estimation accuracy, simple modelling complexity, and multi-temperature prediction capability in the thermal modelling of complex thermal systems, e.g., electrical machines.

29 May 2025 in IEEE Transactions on Industry Applications
Verified
Journal Article
Closed access
Peng WangPeng Wang
Peng Wang
Z. Q. ZhuZ. Q. Zhu
Z. Q. Zhu
Dawei LiangDawei Liang
Dawei Liang
NFNuno M. A. Freire
Nuno M. A. Freire
ZAZiad Azar
Ziad Azar
The rotor position error in sensorless controlled permanent magnet synchronous machines (PMSMs) will lead to parameter estimation errors. In this paper, a novel and simple online parameter estimation method with dual signal injection is proposed for surface-mounted PMSMs under sensorless control, by which the winding inductance, resistance, and rotor flux linkage can be estimated immune to the rotor position error. It is found that the response from ${{q}^e}$-axis voltage caused by injecting a square wave position offset to the estimated rotor position and the response from ${{q}^e}$-axis current caused by injecting a square wave current to the ${{d}^e}$-axis are solely related to winding inductance and resistance errors, respectively. Since the amplitudes of both responses decrease as the parameter errors reduce, the responses in ${{q}^e}$-axis voltage and current are controlled to minimum for estimating the winding inductance and resistance, respectively. At last, the rotor flux linkage is estimated from the observed back-EMF after winding inductance and resistance estimations are completed. The experiments are performed to verify the proposed method.