Prosanta Biswas

Prosanta Biswas

Auto-generated profile, based on publicly available information

Prosanta Biswas

Department of Metallurgical and Materials Engineering, National Institute of Technology, Durgapur, India

Research Focus & Metrics

Academic Career Length

10Years (2017-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
19 November 2019 in Metals and Materials International
Verified
Journal Article
Closed access
PDF file
PBProsanta Biswas
Prosanta Biswas
SPSurajit Patra
Surajit Patra
HRHimadri Roy
Himadri Roy
CTChandra Sekhar Tiwary
Chandra Sekhar Tiwary
MPManas Paliwal
Manas Paliwal
MKManas Kumar kumar
Manas Kumar kumar

3 July 2017 in Canadian Metallurgical Quarterly
Verified
Journal Article
Closed access
PBProsanta Biswas
Prosanta Biswas
MKManas Kumar kumar
Manas Kumar kumar
HRHimadri Roy
Himadri Roy
DMDurbadal Mandal
Durbadal Mandal
In the present investigation, Al–X wt-% Mg2Si (X = 0, 5, 10, 15 and 20) in situ composites are successfully synthesised by one-step gravity casting technique. Commercially pure Al, Mg and Si are used as raw materials. Microstructural evaluation and correlation of micro- and bulk hardness properties have been studied on developing composites. The composites consist of mainly three phases: matrix (α-Al), reinforcing (primary Mg2Si) and binary eutectic (Al–Mg2Si) phase. Primary Mg2Si particles are formed by pseudo-eutectic transformation during solidification and surrounded by matrix and binary eutectic phase. It is found that Mg2Si concentration has a significant impact on morphology and volume per cent of the above-mentioned phases. Primary Mg2Si particles’ size and volume per cent increase with increasing wt-% of Mg2Si. Volume per cent of individual phases and Mg2Si concentration have great impact on hardness properties of composites. Bulk hardness increases with increasing wt-% of Mg2Si concentration, but micro-hardness of primary Mg2Si particle decreases slightly. Mg2Si concentration also has significant impact on micro-hardness of individual phases.

29 January 2023 in Materials Chemistry and Physics
Verified
Journal Article
Closed access
RBRahul Bhandari
Rahul Bhandari
PBProsanta Biswas
Prosanta Biswas
MMManab Mallik
Manab Mallik
MKManas Kumar kumar
Manas Kumar kumar

1 September 2019 in Materials Research Express
Verified
Journal Article
Closed access
PDF file
PBProsanta Biswas
Prosanta Biswas
KPKona Durga Prasadu
Kona Durga Prasadu
MKManas Kumar kumar
Manas Kumar kumar

4 June 2019 in Journal of Tribology
Verified
Journal Article
Closed access
PDF file
PBProsanta Biswas
Prosanta Biswas
MKManas Kumar kumar
Manas Kumar kumar
DMDurbadal Mandal
Durbadal Mandal
The microstructural morphology and wear behavior of as cast Al-X wt.% Mg2Si (X = 0.0, 5.0, 10.0, 15.0 and 20.0) composites were investigated through optical microscopy (OM), energy dispersive X-ray (EDX) spectrometry, scanning electron microscopy (SEM) and field emission scanning electron microscopy (FESEM). The dry sliding wear behavior was studied against an EN 31 hardened steel disk at four different applied loads (19.6 N, 29.4 N, 39.2 N and 49 N) with a sliding speed of 62.8 m/min for 1 hours. The optical microscopy analysis exhibit that the primary Mg2Si particles average equivalent diameter and volume fraction is increased with increase in Mg2Si (Mg and Si) concentration in the Al- Mg2Si composite. Therefore, the bulk hardness of the composites is increased, whereas, the primary Mg2Si hardness decreased, because the coarser primary Mg2Si particles have less compactness. The wear resistance of the commercially pure aluminium significantly improved due to Mg2Si reinforcement and the wear resistance is increased with the increase in Mg2Si concentration up to 15.0 wt.% and then decreased at 20.0 wt.%. The tested composites worn surfaces and debris exhibit adhesion, delamination, microcutting-abrasion, abrasive and oxidation type wear mechanism.

3 May 2020 in International Journal of Cast Metals Research
Verified
Journal Article
Closed access
PBProsanta Biswas
Prosanta Biswas
SPSurajit Patra
Surajit Patra
MKManas Kumar kumar
Manas Kumar kumar
The effect of Zr (0.1, 0.3, 0.5 wt. %) addition on microstructural morphology, hardness, mechanical properties and fracture behaviour of gravity cast Al-12.4Si alloy has been studied. The unmodified Al-12.4Si alloy consists of non-uniformly distributed coarse and irregular shape primary and eutectic silicon particles with sharp corners in Al phase. However, the Zr added Al-12.4Si alloys have uniformly distributed fine eutectic and primary Si particles with blunt corners due to formation of Al3Zr, which acts as heterogeneous nucleation site for Si. The bulk hardness of the modified alloy is slightly increased, but ultimate tensile strength (UTS), yield strength (YS) and elongation (%El) are increased significantly as an effect of microstructural morphology modification. Further, fractographs reveal that the brittle mode of fracture and cleavage fracture of Si particles decreased and ductile fracture with dimples formation increased in the modified alloy.