Nader Morshedian

Nader Morshedian

Auto-generated profile, based on publicly available information

Nader Morshedian

Plasma and Nuclear Fusion Research School, Nuclear Science and Technology Research Institute, Tehran, Iran

Research Focus & Metrics

Academic Career Length

22Years (2005-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 January 2005 in Czechoslovak Journal of Physics
Verified
Journal Article
Closed access
PDF file
SGS. Goudarzi
S. Goudarzi
SKS.M. Sadat Kiai
S.M. Sadat Kiai
NMN. Morshedian
N. Morshedian
ANA. Nasiri
A. Nasiri
RAR. Amrollahi
R. Amrollahi

26 July 2017 in Plasma Science and Technology
Verified
Journal Article
Closed access
PDF file
NMNader Morshedian
Nader Morshedian
The ablation parameters such as threshold fluence, etch depth, ablation rate and the effect of material targets were investigated under the interaction of laser pulse with low intensity. The parameters of the laser system are: laser pulse energy in the range of 110–140 mJ, wavelength 1064 nm and pulse duration 20 ns. By macroscopic estimation of the outward images of the ablation and data obtained, we can conclude that the photothermal and photoionization processes have more influence for aluminum ablation. In contrast, for polymer samples, from the macroscopic observation of the border pattern at the irradiated spot, and also the data obtained from the experiment results, we deduce that both chemical change due to heating and photochemical dissociation were effective mechanisms of ablation. However, concerning the two polymer samples, apart from considering the same theoretical ablation model, it is conceived that the photomehanical specifications of PMMA are involved in the ablation parameters. The threshold fluence for an ablation rate of 30 laser shots were obtained as 12.4, 24.64, and 11.71 J cm−2, for aluminum, silicon rubber and polymethylmethacrylate (PMMA) respectively. The ablation rate is exponentially decreased by the laser-shot number, especially for aluminum. Furthermore, the etch depth after 30 laser shots was measured as 180, 630 and 870 μm, for aluminum, silicon rubber and PMMA, respectively.

1 July 2015 in Physics of Plasmas
Verified
Journal Article
Closed access
PDF file
ABAzadeh Barjasteh
Azadeh Barjasteh
EEEsmaeil Eslami
Esmaeil Eslami
NMNader Morshedian
Nader Morshedian
In this paper, we have presented the experimental and modeling results of the effect of voltage parameters on the characteristics of the low-pressure Ar dielectric barrier discharge. The frequency and amplitude range was set at 5–19 kHz and 255–370 V, respectively. Our investigations showed that the voltage parameters such as amplitude and frequency have large impact on the discharge behavior. Increase in applied voltage amplitude leads to an increase in discharge current. It is also shown that with increasing applied voltage amplitude, the plasma radiations are increased and move to the middle of discharge gap. Also, it causes that surface charge density is increased and discharge is distributed on the dielectric surface. With increasing voltage frequency, discharge current and plasma radiations are increased, but discharge is not distributed on the dielectrics surface. It is also shown that with increasing voltage frequency and amplitude, the discharge kinetic is changed.

31 July 2009 in Quantum Electronics
Verified
Journal Article
Closed access
VBV V Bolshakov
V V Bolshakov
AVA A Vorob'Ev
A A Vorob'Ev
DUDaria Uryupina
Daria Uryupina
KIK A Ivanov
K A Ivanov
NMNader Morshedian
Nader Morshedian
ASAndrei Savel'ev
Andrei Savel'ev

16 June 2015 in Plasma Physics Reports
Verified
Journal Article
Closed access
PDF file
EEE. Eslami
E. Eslami
ABA. Barjasteh
A. Barjasteh
NMN. Morshedian
N. Morshedian
In this work, we numerically compare the effect of a sinusoidal, triangular, and rectangular pulsed voltage profile on the calculated particle production, electric current, and gas voltage in a dielectric barrier discharge. The total argon gas pressure of 400 Pa, the distance between dielectrics of 5 mm, the dielectric thickness of 0.7 mm, and the temperature of T = 300 K were considered as input parameters. The different driving voltage pulse shapes (triangular, rectangular, and sinusoidal) are considered as applied voltage with a frequency of 7 kHz and an amplitude of 700 V peak to peak. It is shown that applying a rectangular voltage, as compared with a sinusoidal or triangle voltage, increases the current peak, while the peak width is decreased. Higher current density is related to high production of charged particles, which leads to the generation of some highly active species, such as Ar* (4s level), and Ar** (4p level) in the gap.

1 June 2016 in Chemical Physics Letters
Verified
Journal Article
Closed access
MEMohammadreza Eidi
Mohammadreza Eidi
MVMohsen Vafaee
Mohsen Vafaee
ANAli Reza Niknam
Ali Reza Niknam
NMNader Morshedian
Nader Morshedian