Jean-Paul Ferrieux

Jean-Paul Ferrieux

Auto-generated profile, based on publicly available information

Jean-Paul Ferrieux

Univ. Grenoble Alpes, 38000 Grenoble, France

Research Focus & Metrics

Academic Career Length

31Years (1996-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 January 1996 in EPE Journal
Verified
Journal Article
Closed access
CACh. Andrieu
Ch. Andrieu
JFJ-.P. Ferrieux
J-.P. Ferrieux
MRM. Rocher
M. Rocher
Over the last few years, power factor correction has become an important field of research, due mainly to changing low frequency EMC standards. Our interest lies in AC/DC conversion from 230 V line voltage. Since July 1 1995 and for this type of line, European standard EN 61000-3-2 has replaced EN 60555–2, which entails great change for low and medium power converters. Usually, the stage between the network and a DC/DC converter is composed of an uncontrolled diode rectifier followed by a structure comprising at least an inductor and a capacitor. First, the capacitor sets the voltage variation in primary DC voltage and the inductor induces the input current waveform. However, these characteristics are not controlled by the typical rectifier and depend on network conditions or on load variations. This low-cost robust system is analysed respecting EN 60555–2 and EN 61000-3-2 criteria. The relation between total harmonic distortion and the power factor is shown. In order to improve the behaviour of this stage, an active component has been added to the existing passive components when redesigning the chopper. This chopper is controlled in “Power Factor Correction” mode i.e. input current is triggered to a sinusoidal current from a loop. Depending on the choice of chopper, one or several high frequency passive components are needed but a low frequency filter (capacitance on output) is still required. The paper goes on to study the use of the boost chopper as a preregulator in association with another converter, and then the use of the insulated flyback converter to supply DC output voltage. For both, the different PFC control modes which enable a sinusoidal line current to be obtained are analysed and discussed for discontinuous and continuous conduction modes.

25 June 2021 in IEEE Journal of Emerging and Selected Topics in Power Electronics
Verified
Journal Article
Closed access
AVAdrien Voldoire
Adrien Voldoire
Jean-Luc SchanenJean-Luc Schanen
Jean-Luc Schanen
JFJean-Paul Ferrieux
Jean-Paul Ferrieux
BSBenoit Sarrazin
Benoit Sarrazin
CGCyrille Gautier
Cyrille Gautier
This article presents an optimization process applied to the sizing of high power silicon carbide inverters. The case study is the design of an aeronautical converter. A gradient-based optimization method is chosen for its ability to explore a wide solution space with a large amount of constraints, what is the case during the pre-design phase. Many topologies are selected and associated models are developed. Among all these models, active and passive component design, and spectral analysis of voltages and currents, are presented. Optimization results, with the goal of minimizing the global mass of the converter, are provided. The different topologies are compared to find the best one for the selected case study. The relevance of the optimization result is evaluated with the study of the optimality of the solution. Finally, experimental results are compared to the optimization ones, which validates the good accuracy of analytical models.

20 January 2003
Verified
Conference Paper
Closed access
Jean-Christophe CrebierJean-Christophe Crebier
Jean-Christophe Crebier
MBM. Brunello
M. Brunello
JFJ.P. Ferrieux
J.P. Ferrieux

13 November 2002
Verified
Conference Paper
Closed access
KLK. Laouamri
K. Laouamri
Jean-Christophe CrebierJean-Christophe Crebier
Jean-Christophe Crebier
JFJ.P. Ferrieux
J.P. Ferrieux
TCT. Chevalier
T. Chevalier

1 September 2011
Verified
Conference Paper
Closed access
BSB. Sarrazin
B. Sarrazin
NRNicolas Rouger
Nicolas Rouger
JFJ.P. Ferrieux
J.P. Ferrieux
YAYvan Avenas
Yvan Avenas
Currently small electric vehicles use low voltage batteries around 48V with high current levels in order to reach a power of several kW for the traction chain. One of the objectives of future converters is to increase the AC amplitude to higher levels (up to 300V) in order to decrease current level, while keeping the same transferred power. As a consequence of higher voltage levels, the global conduction losses will be reduced in the traction chain. Voltage source inverters are generally used in order to drive electric motors. Multilevel voltage source inverters, namely cascaded H-bridge, are under investigation in this paper, in their application to electrical vehicles. This paper presents a numerical and experimental analysis of cascaded H-bridge inverters. The expected benefits of cascaded inverters for electric vehicle are a better management of battery cells, improved output voltage waveforms and spread thermal losses sources. Several parameters and experimental results are investigated in this paper such as converter losses, efficiency, volumes (heat sink, passive components) and spectral analysis of output voltage.

17 October 2017 in AIP Advances
Verified
Journal Article
Open access
RLRichard Lebourgeois
Richard Lebourgeois
ELEric Labouré
Eric Labouré
YLYves Lembeye
Yves Lembeye
JFJean-Paul Ferrieux
Jean-Paul Ferrieux
This paper deals with multilayer magnetic components for power electronics application and specifically for high frequency switching. New formulations based on nickel-zinc-copper spinel ferrites were developed for high power and high frequency applications. These ferrites can be sintered at low temperature (around 900°C) which makes them compatible with the LTCC (Low Temperature Co-fired Ceramics) technology. Metallic parts of silver or gold can be fully integrated inside the ferrite while guaranteeing the integrity of both the ferrite and the metal. To make inductors or transformers with the required properties, it is mandatory to have nonmagnetic parts between the turns of the winding. Then it is essential to find a dielectric material, which can be co-sintered both with the ferrite and the metal. We will present the solution we found to this problem and we will describe the results we obtained for a multilayer co-sintered transformer. We will see that these new components have good performance compared with the state of the art and are very promising for developing high density switching mode power supplies.