26 May 2009 in Nanotechnology
The UV and humidity sensing properties of ZnO nanorods prepared by arc discharge have been studied. Scanning electron microscopy and photoluminescence spectroscopy were carried out to analyze the morphology and optical properties of the as-synthesized ZnO nanorods. Proton induced x-ray emission was used to probe the impurities in the ZnO nanorods. A large quantity of high purity ZnO nanorod structures were obtained with lengths of 0.5–1 µm. The diameters of the as-synthesized ZnO nanorods were found to be between 40 and 400 nm. The nanorods interlace with each other, forming 3D networks which make them suitable for sensing application. The addition of a polymeric film-forming agent (BASF LUVISKOL® VA 64) improved the conductivity, as it facilitates the construction of conducting networks. Ultrasonication helped to separate the ZnO nanorods and disperse them evenly through the polymeric agent. Improved photoconductivity was measured for a ZnO nanorod sensor annealed in air at 200 °C for 30 min. The ZnO nanorod sensors showed a UV-sensitive photoconduction, where the photocurrent increased by nearly four orders of magnitude from 2.7 × 10−10 to 1.0 × 10−6 A at 18 V under 340 nm UV illumination. High humidity sensitivity and good stability were also measured. The resistance of the ZnO nanorod sensor decreased almost linearly with increasing relative humidity (RH). The resistance of the ZnO nanorods changed by approximately five orders of magnitude from 4.35 × 1011 Ω in dry air (7% RH) to about 4.95 × 106 Ω in 95% RH air. It is experimentally demonstrated that ZnO nanorods obtained by the arc discharge method show excellent performance and promise for applications in both UV and humidity sensors.
22 July 2011 in Nanotechnology
Several different synthetic methods have been developed to fabricate tungsten oxide (WO(3)) nanostructures, but most of them require exotic reagents or are unsuitable for mass production. In this paper, we present a systematic investigation demonstrating that arc discharge is a fast and inexpensive synthesis method which can be used to produce high quality tungsten oxide nanostructures for NO(2) gas sensing measurements. The as-synthesized WO(3) nanostructures are characterized by x-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), finger-print Raman spectroscopy and proton induced x-ray emission (PIXE). The analysis shows that spheroidal-shaped monoclinic WO(3) crystal nanostructures were produced with an average diameter of 30 nm (range 10-100 nm) at an arc discharge current of 110 A and 300 Torr oxygen partial pressure. It is found that the morphology is controlled by the arc discharge parameters of current and oxygen partial pressure, e.g. a high arc discharge current combined with a low oxygen partial pressure results in small WO(3) nanostructures with improved conductivity. Sensors produced from the WO(3) nanostructures show a strong response to NO(2) gas at 325 °C. The ability to tune the morphology of the WO(3) nanostructures makes this method ideal for the fabrication of gas sensing materials.
30 May 2006 in IEEE Electron Device Letters
/spl beta/-SiC nanowires were synthesized by the way of high-frequency induction with diameter range between 10 to 25 nm and the length was up to 10 /spl mu/m. Field-effect transistor was fabricated with those synthesized /spl beta/-SiC nanowires. The carrier mobilities of the n-type SiCFETs were 6.4 and 15.9 cm/sup 2//V/spl middot/s when V/sub ds/ is 0.01 and 0.05 V at room temperature, respectively. At high temperature, the drain current increased by one order of magnitude than it did at room temperature. The carrier mobility versus 1000/T agreed well with the Arrhenius function. The SiCFETs in this letter would be used as electrical devices operated in high temperatures because of their superior properties.
1 January 2012 in Chemical Physics Letters
1 December 2010 in Journal of Nanoscience and Nanotechnology
Zinc oxide (ZnO) nanorods have been synthesized via the arc discharge method. Different oxygen partial pressures were applied in the arc discharge chamber to modulate the field emission properties of the as-synthesized ZnO nanorods. Scanning electron microscopy (SEM) was carried out to analyze the morphology of the ZnO nanorods. The ion beam analysis technique of proton induced X-ray emission (PIXE) was performed to probe the impurities in ZnO nanorods. SEM images clearly revealed the formation of randomly oriented ZnO nanorods with diameters between 10–50 nm. It was found that the morphology and the electrical properties of the ZnO nanorods were dependent on the oxygen partial pressure during arc discharge. In addition enhanced UV-sensitive photoconductivity was found for ZnO nanorods synthesized at high oxygen partial pressure during arc discharge. The field emission properties of the nanorods were studied. The turn-on field, which is defined at a current density of 10 A cm−2, was about 3 V m−1 for ZnO nanorods synthesized at 99% oxygen partial pressure during arc discharge. The turn-on field for ZnO nanorods increased with the decrease of oxygen partial pressure during arc discharge. The simplicity of the synthesis route coupled with the modulation of field emission properties due to the arc discharge method make the ZnO nanorods a promising candidate for a low cost and compact cold cathode material.
1 May 2014 in Optical Materials