Asad A. Abidi

Asad A. Abidi

Auto-generated profile, based on publicly available information

Asad A. Abidi

Electrical and Computer Engineering Department, University of California, Los Angeles, CA, USA

Research Focus & Metrics

Academic Career Length

25Years (2002-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
25 April 2019 in IEEE Transactions on Circuits and Systems I: Regular Papers
Verified
Journal Article
Closed access
HXHao Xu
Hao Xu
AAAsad A. Abidi
Asad A. Abidi
We make the case that in most comparators, offset and noise are determined by a dynamic preamplifier always embedded ahead of a regenerative latch. An analysis of this amplifier follows, from which simple expressions are obtained for input-referred offset and noise bandwidth. Practical circuit methods to compensate offset and lower noise become evident. We compare the StrongArm comparator with the double tail topology, and identify requirements for correct operation.

20 February 2019 in IEEE Journal of Solid-State Circuits
Verified
Journal Article
Closed access
JPJiacheng Pan
Jiacheng Pan
AAAsad A. Abidi
Asad A. Abidi
WJWenlong Jiang
Wenlong Jiang
DMDejan Markovic
Dejan Markovic
A method to transmit power and to communicate data in the reverse direction over only one pair of inductive coils is described. The system self-regulates the delivered load voltage, with no monitoring of or explicit feedback from the power receiver. Up to 94 mW of power can be transmitted over distances as large as 4.2 cm using coils of 3 cm diameter. The received voltage is unaffected by changes in coil separation up to a certain limit and also by changes of up to 40x in load current demand. A constant envelope frequency-shift keying (FSK) modulation is also described to transmit data in the reverse channel that exploits mode-selection properties of a free-running oscillator. This allows smooth, uninterrupted delivery of power while data is being transmitted.

12 October 2022 in IEEE Journal of Solid-State Circuits
Verified
Journal Article
Closed access
DYDihang Yang
Dihang Yang
DMDavid Murphy
David Murphy
HDHooman Darabi
Hooman Darabi
ABArya Behzad
Arya Behzad
AAAsad A. Abidi
Asad A. Abidi
WLWeiyu Leng
Weiyu Leng
A low-noise synthesizer design in the millimeter-wave (mm-wave) range is complicated by the invariably large closed-loop gain and the high operation frequency of the voltage-controlled oscillator (VCO). To overcome these challenges, this work proposes a harmonic-mixing synthesizer system with a 188-dB figure-of-merit mm-wave VCO. The synthesizer extends the bandwidth to 5 MHz, thereby suppressing VCO noise. Importantly, DSM is not amplified by the $f_{\rm VCO}/f_{\rm ref}$ gain of the system. A prototype employing a 74-MHz reference achieves a $-$ 250-dB phase-locked loop (PLL) figure of merit with a measured 88-fs rms jitter.

5 January 2022 in IEEE Journal of Solid-State Circuits
Verified
Journal Article
Closed access
KSKejian Shi
Kejian Shi
HDHooman Darabi
Hooman Darabi
AAAsad A. Abidi
Asad A. Abidi
An electrical balance duplexer (EBD) supports dual-band TX-RX isolation enabling frequency-division duplexing (FDD) operation at 5-7 GHz for Wi-Fi 6/6E. A programmable balance network in the EBD can balance the antenna impedance ( $Z_{\text {ANT}}$ ) in the TX channel and RX channel independently and simultaneously. An on-chip passive bandstop filter as a part of the balance network is implemented, achieving sub-2-dB passband insertion loss (IL) and >20-dB stopband rejection with 10% frequency spacing. This filter separates two impedance tuners in the balance network and enables the independent tunability at two bands. A comprehensive and rigorous analysis of general LCR two-ports shows the limit of the $s_{21}$ frequency selectivity when built with finite- $Q$ elements. The analysis guides the filter design, which guarantees the maximum frequency selectivity. The analysis is then extended to LCR ${N}$ -ports as the complete analysis. The EBD provides >40-dB isolation in an 80-MHz channel bandwidth in the TX band (5-6 GHz), for any $Z_{\text {ANT}}(f_{\text {TX}})$ within VSWR = 2, and independently in the RX band (6-7 GHz) when $Q_{\text {ANT}}< 4.3$ . The EBD is designed for ≤4-dB RX IL and ≤3.8-dB TX IL, and it supports +29-dBm TX output. The EBD is implemented in Towerjazz 65-nm RF silicon-on-insulator (SOI) CMOS technology and occupies an area of 2.3 mm 2 .

13 July 2020 in IEEE Journal of Solid-State Circuits
Verified
Journal Article
Closed access
AYAlireza Yousefi
Alireza Yousefi
AAAsad A. Abidi
Asad A. Abidi
DMDejan Markovic
Dejan Markovic
A low-power half-duplex data link transmits data at up to 4 Mb/s over coupled inductors across distances of up to 5 cm. The inductors are part of two resonators which tune a free-running oscillator to one of their natural modes. This gives robustness to changes in coil distance and relative orientation. With load-shift keying (LSK) employed in the remote transponder, the link is modeled analytically to reveal some unexpected properties. A complete design guide aids selection of coil size for range, carrier frequency for data rate, and Q-switching to extend range. Owing to low power circuit design, the remote transponder consumes 0.075 pJ/b in transmit, 5 pJ/b in receive mode.

10 March 2023 in IEEE Transactions on Circuits and Systems I: Regular Papers
Verified
Journal Article
Closed access
KSKejian Shi
Kejian Shi
AAAsad A. Abidi
Asad A. Abidi
HDHooman Darabi
Hooman Darabi
A design-oriented analysis of a transimpedance amplifier (TIA) reveals the optimum compression-free dynamic range for downconverted blockers lying in its 2 nd -order transition band. The unique circuit topology is chosen to eliminate low-frequency zeros of the transfer function to TIA output with only one OpAmp. Two approaches lead to TIA designs with or without capacitive positive feedback. Both configurations are analyzed and discussed. Simple and accurate design equations allow the component value to be selected straightforwardly. $\omega_0$ and $Q$ of the two poles are independently controlled. Analytical expressions for out-of-band (OOB) linearity are derived, explaining different distortion mechanisms from both gate and drain voltages of a FET. The FET gate voltage is shown to affect the distortion even if its swing is much lower than the drain voltage swing. The design fully benefits from 2 nd -order filtering, yielding optimum blocker tolerance. Power dissipation is limited by the requirements for noise figure and independent pole control. A mixer-first receiver that operates from 1 to 7 GHz is realized on 65 nm RF-SOI CMOS. It displays $+$ 31.1 dBm OOB input-referred third-order intercept point (OOB-IIP3), and $+$ 11.8 dBm OOB blocker 1-dB compression point (B1dB). The TIA consumes 22 mW. The prototype verifies the TIA design.