18 March 2008 in Philosophical Transactions of the Royal Society A: Mathematical, Physical and Engineering Sciences
Experimental evidence shows that the presence of an ambient liquid can greatly modify the collision process between two solid surfaces. Interactions between the solid surfaces and the surrounding liquid result in energy dissipation at the particle level, which leads to solid–liquid mixture rheology deviating from dry granular flow behaviour. The present work investigates how the surrounding liquid modifies the impact and rebound of solid spheres. Existing collision models use elastohydrodynamic lubrication (EHL) theory to address the surface deformation under the developing lubrication pressure, thereby coupling the motion of the liquid and solid. With EHL theory, idealized smooth particles are made to rebound from a lubrication film. Modified EHL models, however, allow particles to rebound from mutual contacts of surface asperities, assuming negligible liquid effects. In this work, a new contact mechanism, ‘mixed contact’, is formulated, which considers the interplay between the asperities and the interstitial liquid as part of a hybrid rebound scheme. A recovery factor is further proposed to characterize the additional energy loss due to asperity–liquid interactions. The resulting collision model is evaluated through comparisons with experimental data, exhibiting a better performance than the existing models. In addition to the three non-dimensional numbers that result from the EHL analysis—the wet coefficient of restitution, the particle Stokes number and the elasticity parameter—a fourth parameter is introduced to correlate particle impact momentum to the EHL deformation impulse. This generalized collision model covers a wide range of impact conditions and could be employed in numerical codes to simulate the bulk motion of solid particles with non-negligible liquid effects.
27 December 2017 in Physical Review E
We propose a constitutive model to describe the nonlocality, hysteresis, and several flow features of dry granular materials. Taking the well-known inertial number as a measure of sheared-induced local fluidization, we derive a relaxation model for according to the evolution of microstructure during avalanche and dissipation processes. The model yields a nonmonotonic flow law for a homogeneous flow, accounting for hysteretic solid-fluid transition and intermittency in quasistatic flows. For an inhomogeneous flow, the model predicts a generalized Bagnold shear stress revealing the interplay of two microscopic nonlocal mechanisms: collisions among correlated structures and the diffusion of fluidization within the structures. In describing a uniform flow down an incline, the model reproduces the hysteretic starting and stopping heights and the Pouliquen flow rule for mean velocity. Moreover, a dimensionless parameter reflecting the nonlocal effect on the flow is discovered, which controls the transition between Bagnold and creeping flow dynamics.
2 September 2016 in Granular Matter
1 September 2021 in Physics of Fluids
The effect of non-local momentum transport on a silo discharge process is numerically investigated using a continuum simulation with the rheology model in which the gradient expansion model is adopted to account for the non-local effects due to the non-uniform field of inertial number I [Bouzid et al., Phys. Rev. Lett. 111, 238301 (2013)]. The singularity for I = 0 is handled with a regularization scheme [Lin and Yang, J. Comput. Phys. 420, 109708 (2020)]. Compared to the discharge dynamics predicted with the local rheology model, the non-local effect enhances the velocity field to increase the volume discharge flow rate Q, especially when the silo orifice L is narrower. Both the local and non-local flow simulations conform to the Beverloo relation , where d is the intrinsic grain diameter but the non-local effects appear to lessen the orifice reduction effect coefficient k. The difference between the local and the non-local flow rates , made dimensionless by , grew monotonically with decreasing L/d with a slight enhancement if the silo height-to-width aspect ratio deviates from unity. Finally, we evaluated the ratio of the shear strain rate to the instantaneous maximum value to define a high-shear zone when the ratio is above a threshold and studied its evolution from the onset to the end of the discharge process. Interestingly, non-local momentum transport helped to reduce the size of the high-shear zone to give a more uniformly fluidized central zone above the orifice.
28 September 2015 in Granular Matter
25 August 2020 in Journal of Mechanics
This work examines the μ(I) relation that describes the effective friction coefficient μ of a dense granular flow as a function of flow inertial number I, at the center of a rotating drum from its flow onset to steady state using DEM. We want to see how the internal friction coefficient of an accelerating flow may be predicted so that the associated tangential stress can be estimated with the proper knowledge of the normal stress. Under the three investigated drum speeds (3, 4.5 and 6 rpm), the bulk normal stress, σn(y), is found to be a consistent linear depth profile throughout the flow development with a slope degraded from the hydrostatic value, Ph(y), due to lateral wall friction. With the discovery of a non-constant depth-decaying effective wall friction coefficient, we derive analytically a wall-degradation factor K(h) to give σn(y)= K(h)Ph(y). The depth profile of tangential stress, however, varies in time from a concave shape upon acceleration, τa(y), to a more linear trend at the steady state, τss(y). Hence, the μa-Ia profile (with μa=τ/σn) upon flow acceleration offsets from the steady μss(Iss) relation. A pseudo-steady acceleration modification number, ΔI, is proposed to shift the inertial number in the acceleration phase to I* = Ia+ΔI so that the μa-I* data converge to μss(Iss). This finding shall allow us to predict a transient tangential stress by τa(y) = μss(I*)K(y)Ph(y) using the well-accepted knowledge of steady flow rheology, hydrostatic pressure, and the currently developed wall-degradation factor.