R. Wayne Johnson

R. Wayne Johnson

Auto-generated profile, based on publicly available information

R. Wayne Johnson

Department of Electrical and Computer Engineering, Tennessee Tech University, Cookeville, TN, USA

Research Focus & Metrics

Academic Career Length

37Years (1990-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 February 2019 in International Journal of Heat and Mass Transfer
Verified
Journal Article
Closed access
FMFarzin Mashali
Farzin Mashali
ELEthan Mohseni Languri
Ethan Mohseni Languri
JDJim Davidson
Jim Davidson
DKDavid Kerns
David Kerns
WJWayne Johnson
Wayne Johnson
GCGlenn Cunningham
Glenn Cunningham

1 June 1990 in IEEE Transactions on Components, Hybrids, and Manufacturing Technology
Verified
Journal Article
Closed access
RJR.W. Johnson
R.W. Johnson
TPT.L. Phillips
T.L. Phillips
WWW.K. Weidner
W.K. Weidner
SHS.F. Hahn
S.F. Hahn
DBD.C. Burdeaux
D.C. Burdeaux
PTP.H. Townsend
P.H. Townsend

1 April 2011 in Journal of the American Helicopter Society
Verified
Journal Article
Open access
ADAnubhav Datta
Anubhav Datta
WJWayne Johnson
Wayne Johnson

4 April 2019 in IEEE Transactions on Components, Packaging and Manufacturing Technology
Verified
Journal Article
Closed access
ARAnto Raj
Anto Raj
TSThomas Sanders
Thomas Sanders
SSSharath Sridhar
Sharath Sridhar
JEJohn L. Evans
John L. Evans
MBMichael J. Bozack
Michael J. Bozack
DCD. Mark Carpenter
D. Mark Carpenter
This paper offers a statistical methodology for evaluating Pb-free solder alloy performance for high-reliability products using Cox proportional regression analysis and provides a detailed application of the technique based upon a 15-mm BGA package. Specifically, the effects of doping SAC305 solder balls with small amounts of Bi, Co, In, Mn, Ni, and Sb either directly or from the solder paste used for assembly have been studied. The test results have led to a down-selection of optimum material combinations that offer a potential solution to the wellknown material degradation of SAC305 solder alloys with aging. The test conditions had two different time/temperature periods: 10 days at 25 °C and an accelerated condition of 180 days at 125 °C. Each test board was temperature shocked 3000 times (-40 °C-125 °C) with a 15-min thermal profile (5-min dwell time and 2.5-min transition time). The electrical continuity of solder interconnect was examined during the tests, and the effect of solder doping and aging on the failure rate (hazard rate) were assessed at 90% confidence level using the proportional hazard model. We found that the solder doping combination, aging time and temperature, and the interactions between these parameters have significant impacts on the failure rate. BGA with Sn-Ag- Cu doped with Sb, Bi, Co, and Ni can significantly reduce the failure rate after aging with a 90% level of confidence. The failure analysis shows recrystallized assisted crack nucleation in the solder joints.

1 January 2014 in Additional Conferences (Device Packaging, Hitec, Hiten, & Cicmt)
Verified
Journal Article
Closed access
FYFang Yu
Fang Yu
RJR. Wayne Johnson
R. Wayne Johnson
MHMichael Hamilton
Michael Hamilton
Low temperature Ag sintering technology provides a lead-free die attachment compatible with high temperature (300°C) applications. Previous work with Ag sintering has required pressure during the sintering process or been limited to small area die. In this paper, the pressureless sintering of micro-scale silver paste is examined for larger (8mm × 8mm) area die. Experimental combinations included: Si die metallization (Ag and Au); thick film substrate metallization (Au, Ag and PdAg); and sintering temperature. For Au metallization (die and/or substrate), the initial shear strength results were good with 8mm × 8mm die sintered at lower temperatures (200°C). The shear strength was beyond the limit of the shear test machine (100 kg), corresponding to >15.3 MPa. However, after aging for 24 hours at 300°C, the shear strength dropped significantly. An SEM was used to characterize cross sections of as-built and aged sample. The decrease in die shear strength with high temperature sintering (250°C and 300°C) or high temperature aging is attributed to surface diffusion of Ag along the Au surface resulting in a dense Ag layer adjacent to the Au surface and a depletion layer within the die attach adjacent to the dense Ag layer. Shear failures occurred through the depleted region. For Ag metallization (die and substrate), no decrease in shear strength was observed with 300°C aging. Shear strength of 8 mm × 8 mm dies was >100 kg ( >15.3 MPa) as-built. The shear strength remained >15.3MPa after 3000 hours of 300°C aging.

5 April 2018 in IEEE Transactions on Components, Packaging and Manufacturing Technology
Verified
Journal Article
Closed access
ZZZhangming Zhou
Zhangming Zhou
JCJinzi Cui
Jinzi Cui
FYFang Yu
Fang Yu
RJR. Wayne Johnson
R. Wayne Johnson
MHMichael C. Hamilton
Michael C. Hamilton
High-temperature electronics are required for applications such as automotive, down-hole drilling for oil and geothermal energy, aircraft, and space exploration. SiC and GaN devices are capable of operating in these high-temperature environments and challenging the packaging materials and technology to be compatible with these environments. Thick-film materials and technology have the potential of building reliable interconnections at high temperatures. This paper investigated the electrical reliability of two thick-film conductors (PtPdAu, Au) and two dielectrics at 300 °C. Test vehicles were fabricated with thick-film materials as capacitor and interdigitated finger test structures. For the test vehicles with PtPdAu thick-film, the leakage current of the capacitor structures with thin multilayer dielectrics increased in a short time during 300 °C aging with a 100-V bias, while the leakage current of capacitor structures with thick dielectrics had only a slight increase or remained constant during 300 °C aging with bias. Cross-sectional scanning electron microscopy and energy dispersive spectroscopy analysis showed that bismuth (Bi) in the PtPdAu paste diffused into the dielectrics from both the top and bottom conductors during the high-temperature firing steps in fabrication. If the Bi was continuous through the thin dielectric, the leakage current increased during aging with bias. The leakage current of the Au conductor in capacitor and interdigitated finger structures (both thick and thin dielectrics) did not increase with biased aging in high temperature. The Au conductor did not contain Bi.