8 June 2020 in IEEE Transactions on Antennas and Propagation
In this communication, a compact vertically-integrated full-duplex filtenna is developed by using common feeding and radiating substrate integrated waveguide (SIW) cavities. A rectangular dual-mode SIW cavity, operating at its two orthogonal TE120 and TE210 modes, is first employed as the common feeding cavity to realize two passbands. And then, a common radiating square slot-loaded SIW cavity is vertically integrated with the common feeding cavity so as to enhance the operational bandwidth and improve the frequency selectivity for both two passbands. Two metallic posts are utilized to achieve the desired coupling strength between the feeding and radiating cavities for the two passbands, respectively. By properly arranging the locations of two input ports and coupling regions, high isolation between the two input ports is realized. The detailed design process based on the coupling matrix is presented. To verify the proposed concept, a prototype is fabricated and measured. The measurement results agree well with the simulated values, showing the maximum broadside realized gains of 4.36 dBi and 4.83 dBi, and the impedance bandwidths of 3.2% (4.03–4.16 GHz) and 3.9% (4.81–5 GHz) for the lower and upper passbands, respectively. The proposed antenna also exhibits good performance in terms of port isolation, flat in-band gain response, and out-of-band frequency selectivity.
15 February 2023 in IEEE Transactions on Antennas and Propagation
In this communication, a single-layer, wideband, differential-fed filtering antenna with high selectivity is proposed. The developed filtering antenna possesses a simple structure and consists of a square patch, a square substrate integrated waveguide (SIW) cavity, a pair of symbiotic stepped impedance resonators (SSIRs), and a pair of complementary split ring resonators (CSRRs). The SIW cavity formed with sparse metallized posts is embedded in the square patch, and the impedance bandwidth can be broadened by merging the TM10 mode of the square patch, excited by the electromagnetic energy escaping from the sparse posts, with the TE210 mode in the SIW cavity through differential excitation. The SSIRs are connected with both radiating edges of the square patch. And two extra in-band resonances together with an upper-edge radiation null are simultaneously generated, so the impedance bandwidth and the frequency selectivity at higher stopband can be significantly improved. The CSRRs, surrounding around the differential excitation ports, are etched into the bottom surface of the SIW cavity, and a lower-edge radiation null is produced to further sharpen the roll-off rate. By adjusting the geometrical parameters of the SSIRs and CSRRs, the positions of the two radiation nulls can be independently controlled. For verifying the design method, a prototype of the developed single-layer filtering antenna has been fabricated and tested. The measurement results are well consistent with the simulated values, indicating good performance with a large -10 dB fractional impedance bandwidth of 21.2%, a peak realized gain of 9.3 dBi, two out-of-band rejection levels more than 26 dB, and very high selectivity.
1 September 2022 in IEEE Transactions on Circuits and Systems II: Express Briefs
A low-profile single-layer half-mode substrate integrated waveguide (HMSIW) filtering antenna with compact circuit size is presented in this brief. The antenna features simple structure and consists of a half-mode substrate integrated waveguide cavity (HMSIWC), a shorted parasitic patch, and a folded defected ground structure (DGS) etched into the metallized ground plane. The half-mode technology is employed to reduce the overall dimension in the design. The shorted parasitic patch and the HMSIWC, both operating at half-mode states, are coupled with each other to form a second-order filtering response. And also a radiation null at higher stopband is introduced owing to the effects of the cross coupling. Furtherly, by etching a folded DGS into the metallized ground plane, an additional resonance in the passband and a controllable radiation null at lower stopband are simultaneously generated to broaden the impedance bandwidth and improve the selectivity of lower stopband respectively. For verification, a prototype of the developed HMSIW filtering antenna is designed, fabricated, and measured. The measured and simulated results are in good agreement, showing a wide impedance bandwidth of 9.2% at center frequency of 2.84 GHz, a flat in-band gain response with two controllable radiation nulls at both edges of the operating band, and a maximum boresight realized gain of 5.75 dBi. The proposed HMSIW filtering antenna demonstrates good in-band and out-of-band performance even with a very low profile of $0.015~\mathbf {\mathrm {\lambda }} _{0}$ .
2 June 2021 in IEEE Transactions on Antennas and Propagation
A compact, differential diplex filtenna (DDF) with common-mode (CM) suppression is presented. A rectangular dual-mode patch is developed that operates in both its TM 10 mode and a reshaped TM 30 mode to realize two passbands. Two capacitively loaded loop (CLL) resonators that work at different frequencies are combined with the dual-mode patch to enhance its operational bandwidth and to provide a second-order Chebyshev filter response for both passbands. A slot-coupled differential feed is adopted to suppress the harmonic and CM noise and to obtain symmetrical radiation patterns with low cross-polarization levels. The design process, which is based on filter synthesis theory, is detailed. A prototype operating over the 2.4G and 5.8G WLAN bands was fabricated, assembled, and tested. The measured results, in good agreement with their simulated values, confirm that it attains maximum broadside realized gains of 5.45 and 8.5 dBi and −10 dB fractional impedance bandwidths of 2.4% (2.42–2.48 GHz) and 5.2% (5.65–5.95 GHz) for the lower and upper passbands, respectively. Moreover, it exhibits good out-of-band rejection levels of 18 and 29 dB for the lower and upper stopbands, respectively.
15 November 2024 in IEEE Antennas and Wireless Propagation Letters
In this paper, the single-layer wideband and dual-band end-fire filtering antennas with high front-to-back ratio (FTBR) are developed. The wideband design mainly consists of five parts: the double-sided parallel-strip line (DSPSL) feeding structure, two sets of driven elements, the parasitic strips, the directors, and the U-shaped ground. Herein, the adoption of two sets of driven elements realizes a natural lower radiation null, while the incorporation of parasitic strips facilitates an upper radiation null. The dual-band design is achieved by simply loading the additional longer parasitic strips on the wideband design, which creates a middle radiation null between the two bands. Including the elaborated ground and the directors effectively enhances the FTBR of both designs. For verification, prototypes were manufactured and measured, and the measured results are in good agreement with the simulated ones. The overlapped bandwidth (|S 11 | ≤ −10 dB and FTBR ≥ 15 dB) of the wideband design reaches 54.3%, and that of the dual-band design is 33.6% and 15.5%, respectively. Moreover, both designs exhibit good frequency selectivity with multiple radiation nulls.
27 June 2024 in IEEE Antennas and Wireless Propagation Letters
A single-layer differentially-fed circularly-polarized filtenna with common-mode rejection is presented in this letter. It is composed of a circular patch, a circular substrate integrated waveguide (SIW) cavity, a rectangle slot, two pairs of L -shaped slots, and four pairs of shorting posts. The circular SIW cavity formed with sparse metal posts is embedded in the circular patch, and its two degenerate TM 11 modes are excited though loading the rectangular slot. The two degenerate TM 11 modes of the circular patch can be effectively excited due to the leaked energy from the SIW cavity, thus forming the circularly-polarized (CP) radiation while maintaining a good filtering response. The resonant frequencies of the two pair degenerate modes can be reallocated by altering the spacing of adjacent posts of the SIW cavity, and employing two pairs of L -shaped slots and four pairs of shorting posts. By combining the two pair of degenerated modes, a wide axial ratio (AR) bandwidth with two minima can be obtained. The measured results, in good agreement with the simulated ones, exhibiting a -10dB impedance bandwidth of 8.3%, a 3dB AR bandwidth of 5.6%, and a peak realized gain of 10dBic. The developed antenna features a low profile of 0.025λ 0 while maintaining good filtering performance and common-mode rejection.