In this work, the efficiency of the treated plant Carpobrotus edulis (TPCE) as an effective biosorbent for removing the orange G (OG) and crystal violet (CV) dyes from aqueous solution was investigated. TPCE was characterized by FT-IR, Ss, pHz and SEM-EDX. The influence of parameters such as bioadsorbent dose, contact time, initial concentration, temperature and pH was tested using Taguchi experimental design (TED) with L8 orthogonal array (five parameters in two levels). The initial concentration, bioadsorbent dose and contact time are the main parameters for the removal of CV and OG dyes, while the effects of pH and temperature are minimal. The maximum removal efficiency of dyes under optimal operating conditions was 97.93 % and 92.68 %, respectively. which at the optimal conditions of 3 g/L, pH 10, 20 mg/L, 35 °C, 5 min and 15 g/L, pH 4, 20 mg/L, 35 °C, 60 min for CV and OG dyes, respectively. The results of response surface methodology (RSM) and analysis of variance (ANOVA) showed that the initial concentration Ci of CV dye was the most significant factor in the adsorption efficiency with a contribution of 51.56 %. On the other hand, the OG bioadsorbent dose is the most important factor in adsorption efficiency with a percentage contribution of 56.41 %. The Density Functional Tight Binding (DFTB) method shows that dyes strongly bind the adsorbent surface. Monte Carlo and molecular dynamics simulations show significant interactions between dye and adsorbent surface. The reusability of biomaterial indicated that the adsorption performance dropped very slightly up to five cycles.
The development of heterostructures incorporating photocatalysts optimized for visible-light activity represents a major breakthrough in the field of environmental remediation research, offering innovative and sustainable solutions for environmental purification. This study explores the photocatalytic capabilities of a SnFe2O4/g-C3N4 heterojunction nanocomposite, successfully synthesized from graphitic carbon nitride (g-C3N4) and tin ferrate (SnFe2O4) and applied to the degradation of the cationic dye brilliant cresyl blue (BCB) in an aqueous solution. These two components are particularly attractive due to their low cost and ease of fabrication. Various characterization techniques, including XRD, FTIR, SEM, and TEM, were used to confirm the successful integration of SnFe2O4 and g-C3N4 phases in the synthesized catalysts. The photocatalytic and photo-Fenton-like activity of the heterojunction composites was evaluated by the degradation of brilliant cresyl blue under visible LED illumination. Compared to the pure components SnFe2O4 and g-C3N4, the SnFe2O4/g-C3N4 nanocomposite demonstrated a superior photocatalytic performance. Furthermore, the photo-Fenton-like performance of the composites is much higher than the photocatalytic performances. The significant improvement in photo-Fenton activity is attributed to the synergistic effect between SnFe2O4 and g-C3N4, as well as the efficient separation of photoexcited electron/hole pairs. The recyclability of the SnFe2O4/g-C3N4 composite toward BCB photo-Fenton like degradation was also shown. This study aimed to assess the modeling and optimization of photo-Fenton-like removal BCB using the SnFe2O4/g-C3N4 nanomaterial. The main parameters (photocatalyst dose, initial dye concentration, H2O2 volume, and reaction time) affecting this system were modeled by two approaches: a response surface methodology (RSM) based on a Box–Behnken design and artificial neural network (ANN). A comparison was made between the predictive accuracy of RSM for brilliant cresyl blue (BCB) removal and that of the artificial neural network (ANN) approach. Both methodologies provided satisfactory and comparable predictions, achieving R2 values of 0.97 for RSM and 0.99 for ANN.
The present research work revolves around the evaluation of the elimination of the cationic dye Methylene Blue (MB) from an aqueous solution by the exploitation of natural clay (TMG) from South-East Morocco. Several physicochemical techniques were used to characterize our TMG adsorbate, namely: X-ray diffraction (XRD), Fourier transform infrared absorption spectroscopy (FTIR), differential thermal analysis (DTA), thermal gravimetric analysis (TGA), and zero charge point (pHpzc). The morphological properties and elemental composition of our material were identified using scanning electron microscopy coupled with an energy-dispersive X-ray spectrometer (SEM-EDS). The batch technique was used under different operating conditions to produce quantitative adsorption, namely the amount of adsorbent, dye concentration, contact time, pH, and solution temperature. The maximum adsorption capacity of MB on TMG was 81.185 mg g-1 for a concentration of 100 mg L-1 MB at pHinitial= 6.43, temperature 20 °C, and 1 g L-1 adsorbent. The adsorption data were examined by Langmuir, Freundlich, and Temkin isotherms. The Langmuir isotherm provides the best correlation with the experimental data, and the pseudo-second-order kinetic model is more appropriate for the adsorption of the MB dye. The thermodynamic study of MB adsorption indicates that the process is physical, endothermic, and spontaneous. The Box-Behnken method was applied to identify the optimal conditions for MB removal in the design of batch experiments. The parameters examined result in >99% removal.