Nando Kaminski

Nando Kaminski

Auto-generated profile, based on publicly available information

Nando Kaminski

University of Bremen

Research Focus & Metrics

Academic Career Length

29Years (1998-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 May 2014 in IET Circuits, Devices & Systems
Verified
Journal Article
Open access
PDF file
NKNando Kaminski
Nando Kaminski
OHOliver Hilt
Oliver Hilt
Silicon carbide (SiC)‐diodes have been commercially available since 2001 and various SiC‐switches have been launched recently. Parallelly, gallium nitride (GaN) is moving into power electronics and the first low‐voltage devices are already on the market. Currently, it seems that GaN‐transistors are ideal for high frequency ICs up to 1kV (maybe 2kV) and maximum a few 10A. SiC transistors are better suited for discrete devices or modules blocking 1kV and above and virtually no limit in the current but in that range they will face strong competition from the silicon insulated gate bipolar transistors (IGBTs). SiC and GaN Schottky‐diodes would offer a similar performance, hence here it becomes apparent that material cost and quality will finally decide the commercial success of wide bandgap devices. Bulk GaN is still prohibitively expensive, whereas GaN on silicon would offer an unrivalled cost advantage. Devices made from the latter could be even cheaper than silicon devices. However, packaging is already a limiting factor for silicon devices even more so in exploiting the advantage of wide bandgap materials with respect to switching speed and high temperature operation. After all, reliability is a must for any device no matter which material it is made of.

1 May 2015
Verified
Conference Paper
Closed access
CZChristian Zorn
Christian Zorn
NKNando Kaminski
Nando Kaminski
The temperature-humidity-bias (THB) test is the standard for accelerated stress testing with respect to corrosion and other humidity driven degradation mechanisms. Usually, 1000 hrs tests at 85 degree Celsius and 85 percent relative humidity (85/85) are used to predict up to 25 years of operation. With regard to the respective standards asking for limited self-heating, the bias was commonly limited to 80 V. Nevertheless, recent THB tests on 1.7 kV IGBT modules have shown that higher bias is a more severe test condition. Failure analysis confirmed corrosion of the Al chip-metallization as well as Cu-and Ag-dendrites as the relevant failure mechanisms. In order to determine the acceleration due to bias, 1.2 kV IGBT-modules were tested in THB at 65 percent and 90 percent of their nominal voltage Vnom, respectively. A characteristic degradation consisting of three phases has been identified. The 2nd phase seems to be determined by Al corrosion and a factor of about two has been estimated for the acceleration between the aforementioned test-voltages. Within the 3rd phase, the devices stabilized probably due to localized self-heating. Thus, this degradation mechanism is kind of self-limiting, but the higher leakage increases the risk of thermal runaway, i.e. catastrophic breakdown especially when biased close to Vnom.

1 December 2015 in IET Power Electronics
Verified
Journal Article
Open access
PDF file
CZChristian Zorn
Christian Zorn
NKNando Kaminski
Nando Kaminski
The temperature–humidity–bias (THB) test is the standard for accelerated stress testing with respect to corrosion and other humidity driven degradation mechanisms. Usually, 1000 h tests at 85°C and 85% relative humidity are used to predict up to 25 years of operation. The bias is usually limited to 80 V in order to fulfil the respective standards. Nevertheless, THB tests on 1700 V insulated‐gate bipolar transistor (IGBT)‐modules have shown that higher bias is a more severe test condition. The failure analysis confirmed Cu‐ and Ag‐dendrites and corrosion of the aluminium (Al)‐chip‐metallisation as the relevant failure mechanisms. To determine the acceleration factor due to voltage, 1200 V IGBT modules were tested in THB at 780 V (65% of V CES ) and 1080 V (90% of V CES ). A characteristic degradation consisting of three phases has been identified. The second phase seems to be determined by Al corrosion and an acceleration factor of about two has been estimated from 780 to 1080 V. Within the third phase, the devices stabilised probably due to localised self‐heating. Thus, this degradation mechanism is kind of self‐limiting, but the higher leakage also increases the risk of thermal runaway especially when biased close to the rated collector–emitter voltage.

1 March 1999 in IEEE Transactions on Electron Devices
Verified
Journal Article
Closed access
MLM. Lades
M. Lades
WKW. Kaindl
W. Kaindl
NKN. Kaminski
N. Kaminski
ENE. Niemann
E. Niemann
GWG. Wachutka
G. Wachutka
The influence of incomplete ionization of dopants in 4H/6H-SiC on transient device behavior has been investigated numerically based on a self-consistent solution of the coupled system of Poisson's equation, the continuity equations of electrons and holes, and balance equations for each donor or acceptor level. If the rise time of a reverse bias pulse is equal or smaller than the characteristic ionization time constant, a dynamically enlarged extension of depletion regions is obtained which can result in a dynamic punchthrough (PT) within back-to-back junction configurations. The respective time constants of nitrogen (N), aluminum (Al), and boron (B) mere measured as functions of temperature in 4H- and 6H-SiC using thermal admittance spectroscopy (AS) and deep level transient spectroscopy (DLTS). At room temperature, for instance, we obtained 60 ps/2 ps, 300 ps/10 ps, and 100 ns/100 ns for N (cubic site), Al, and B in 4H/6H-SiC, respectively. As the time constants of N and Al are small, transient incomplete ionization turns out to be negligible, at least within today's high-power device operation areas. Boron, on the other hand, influences significantly the dynamic device characteristics. In order to demonstrate the implications of these effects, numerical device simulations of a 6H-SiC double-implanted MOSFET and a 4H-SiC thyristor were performed. These simulations allow a detailed analysis of the transient device behavior and the onset of dynamic PT which strongly depends on temperature, structure parameters, and the external excitation.

4 November 2015 in Physica Status Solidi (a)
Verified
Journal Article
Closed access
PDF file
VKVibhor Kumar
Vibhor Kumar
NKNando Kaminski
Nando Kaminski
AMAnup Singh Maan
Anup Singh Maan
JAJamil Akhtar
Jamil Akhtar

1 June 2009 in 2009 21st International Symposium on Power Semiconductor Devices & IC's
Verified
Conference Paper
Closed access
AKA. Kopta
A. Kopta
MRM. Rahimo
M. Rahimo
USU. Schlapbach
U. Schlapbach
NKN. Kaminski
N. Kaminski
DSD. Silber
D. Silber
In this paper, the destruction mechanism, which limits the short-circuit capability of high voltage IGBTs utilizing N-buffer structures will be described. The failure mechanism was studied using a combination of device simulations and experimental investigations of 3.3 kV, 4.5 kV and 6.5 kV IGBTs. It was found that the limiting short-circuit failure in these IGBTs is caused by a current filamentation mechanism, which is associated to a distortion of the electric field triggered by a positive feedback effect between the carrier drift velocities and the electric field and the resulting potential distribution in the IGBT N-base.