13 February 2016 in Journal of Synchrotron Radiation
1 March 2008 in Journal of Vacuum Science & Technology B: Microelectronics and Nanometer Structures Processing, Measurement, and Phenomena
1 May 2010 in Journal of Vacuum Science & Technology B
In this article the authors present the potential of ionic liquid ion sources (ILISs) for direct microfabrication of silicon structures. The authors have developed a specific source geometry using the ionic liquid EMI-BF4 to obtain stable emission currents up to the 10 μA regime. ILIS (EMI-BF4) engraving properties were then investigated. The results and the chemical analysis of the patterned substrates suggest that reactive ion species can be generated from ILIS. This possibility is of major interest to allow decisive advances in the field of focused ion beam applications.
1 September 2006 in Journal of Vacuum Science & Technology B: Microelectronics and Nanometer Structures Processing, Measurement, and Phenomena
Inductively coupled plasma etching using Cl2–H2 chemistry with no additive gas (CH4, Ar, or N2) is studied to realize deep (>5μm) ridges with smooth and vertical sidewalls. The process is optimized for nonthermalized InP wafers to avoid the use of thermal grease. Cleaning of the rear side of the wafer after etching is avoided, which is suitable for an industrial process or for critical subsequent steps such as epitaxial regrowth. The influence of the Cl2∕H2 ratio on the etching mechanism is investigated for both InP bulk layers and InGaAs∕InP or InGaAlAs∕InP heterostructures. The authors show that this ratio is the main parameter controlling the ridge profile, in a similar way for both bulk InP and InGa(Al)As∕InP samples. Smooth and vertical sidewalls with neither undercuts nor notches can be obtained in the 0.5–1mT pressure range for a hydrogen percentage of 35%–45% in the gas mixture. Etching rates from 900to1300nm∕min together with a selectivity over SiNx dielectric mask as high as 24:1–29:1 are measured for the InP bulk layers under these conditions. Etching does not affect the optical quality of the heterostructures as evidenced from micro-photoluminescence measurements performed on 1.6-to0.85-μm-wide deep etched ridge waveguides. The process is well adapted to the realization of low loss deep ridge waveguides or buried heterostructures.
1 March 2010 in Journal of Vacuum Science & Technology A
A study is undertaken of the loss kinetics of H and Cl atoms in an inductively coupled plasma (ICP) reactor used for the etching of III-V semiconductor materials. A time-resolved optical emission spectroscopy technique, also referred to as pulsed induced fluorescence (PIF), has been combined with time-resolved microwave hairpin probe measurements of the electron density in a pulsed Cl2/H2-based discharge for this purpose. The surface loss rate of H, kwH, was measured in H2 plasma and was found to lie in the 125–500 s−1 range (γH surface recombination coefficient of ∼0.006–0.023), depending on the reactor walls conditioning. The PIF technique was then evaluated for the derivation of kwCl, and γCl in Cl2-based plasmas. In contrast to H2 plasma, significant variations in the electron density may occur over the millisecond time scale corresponding to Cl2 dissociation at the rising edge of the plasma pulse. By comparing the temporal evolution of the electron density and the Ar-line intensity curves with 10% of Ar added in the discharge, the authors show that a time-resolved actinometry procedure using Ar as an actinometer is valid at low to moderate ICP powers to estimate the Cl loss rate. They measured a Cl loss rate of ∼125–200 s−1 (0.03≤γCl≤0.06) at 150 W ICP power for a reactor state close to etching conditions. The Cl surface loss rate was also estimated for high ICP power (800 W) following the same procedure, giving a value of ∼130–150 s−1 (γCl∼0.04), which is close to that measured at 150 W ICP power.
15 April 2014 in Physica Status Solidi (RRL) – Rapid Research Letters