18 March 2022 in The International Journal of Advanced Manufacturing Technology
1 January 2023 in Materials Research Express
The deformation behavior and mechanical properties based on the aluminum-lithium alloys (FMLs) was investigated to optimize the manufacturing process and further interface interaction. The primary structures of the FML composites were made with two sets of plies. From there, six secondary composites with different fibre sheet orientations were made. Then, interlaminar tensile, flexural, and peeling properties of FMLs were tested. The fiber orientation role in the case of failure behaviors of FMLs under different conditions was also revealed. The results have indicated that the plies design significantly enhanced the interlaminar properties of the FMLs and orientation of fiber laying has significantly affected the flexural strength. The peeling test has shown higher fiber-to-metal interfacial bonding with the value of ≥80 N m−2 over metal-to-metal adhesion. The plies increase the mechanical properties of composite based at fiber orientation and thickness, but too much impairs performance. The 3/2 plies showed a value of ≤385 MPa, which has better results in axial structure analysis than over 4/2 composite layers. The peak values appeared under different parameters like adhesive bonding and parallel fiber orientation, represented in the qualitative analysis section. The surface microscopy of aluminum-lithium alloy sheet and cross-section failure morphology of composite has been done at a different sighting. Surface characterization, fiber orientation breakdown, and deformation morphology have been studied concerning alloys’ elongated grains and micro pits.
23 August 2023 in Materials Today: Proceedings
6 December 2023 in Manufacturing Technology
The electrochemical discharge machining (ECDM) process is developing into a potentially useful method of performing machining in conductive or non-conductive materials. The experiment was conducted utilizing full factorial design (2 4) with the 16 run test. The present study implemented artificial neural network (ANN) and particle swarm optimization (PSO) techniques to predict the Material Removal Rate (MRR) and surface roughness (SR), and the linear regression analysis were utilized for this purpose. The input parameters were adjusted with the objective of maximizing the MRR and minimizing the SR. The four selected process parameters are voltage, gap width, electrode type, and type of electrolyte, with each parameter has two levels, copper and brass were chosen as the electrodes in this particular technique. Linear regression (LR) modelling was calculated for comparison between the ANN model and LR. Artificial neural network (ANN) models have been developed to accurately predict SR and MRR, achieving a prediction accuracy of over 90%. The impacts of these findings have great significance for the future of machining tungsten carbide utilizing ECDM. Based on the results of R 2 , the modelling with ANN is closer to the actual value than the prediction using a linear regression model, the value of R 2 ANN greater than LR so that the prediction model of ANN is still the best model.
28 February 2023 in Egyptian Journal of Chemistry
Fabrics with antibacterial assets have become essential to organize and manage the infestation by microbes and to reduce the formation of odor. The fabrics with antimicrobial finishes are subjected to subsequent washings and their effectiveness after each wash is of prime concern when consumed by human beings. Cotton fabric has large advantages such as compatibility, absorbency, good dimensional stability, and lower shrinkage. One of their major draw backs is that their degradation occurs due to the bacteria on them. In order to evaluate antimicrobial activity, we have prepared natural and organic extracts from peels of wild tree Melia azedarachayan (common name Bakaayan) plant berry. The Bakaayan berries were kept in the ethyl acetate for two weeks and a pitch of berry was obtained through the distillation process and applied to the fabric by padding and anti-microbial activities were analyzed after 24 hours by studying bacteria growth on the fabric. After analyzing bacterial growth on fabric by microscope the extracted pitch was found as antimicrobial. In a study, the fabric samples were tested for antimicrobial activity against bacterial strains like Staphylococcus, E. coli, Bacillus, C. albicans under qualitative and quantitative analysis. The results of the study have indicated that the cotton fabric shows a better microbial resistance against the above-mentioned strains except for C. albicans. As per quantitative analysis, the fabric treated with anti-microbial extract showed the best reduction against Staphylococcus. For analyzing the effect of washing on antimicrobial activity; the finished fabrics were washed according to the standard ISO 6330. The washing result shows a gradual decrease in antimicrobial activity after each wash.
1 February 2024 in Surface Engineering and Applied Electrochemistry
Abrasive water jet (AWJ) cutting is an emerging material processing technology with significant advantages, such as no thermal deformation, high processing