14 April 2020 in Nuclear Technology
The Organisation for Economic Co-operation and Development (OECD)/Nuclear Energy Agency (NEA) Benchmark Study of the Accident at the Fukushima Daiichi Nuclear Power Station (BSAF), which started in 2012 and continued until 2018, was one of the earliest responses to the accident at Fukushima Daiichi. The project, divided into two phases, addressed the investigation of the accident at Units 1, 2, and 3 by severe accident (SA) codes until 500 h, focusing on thermal hydraulics, core relocation, molten corium concrete interaction (MCCI), and fission product release and transport. The objectives of the BSAF were to make up plausible scenarios based primarily on SA forensic analysis, support the decommissioning, and inform SA code modeling. The analysis and comparison among the institutes have brought up vital insights regarding the accident progression, identifying periods of core meltdown and relocation and reactor pressure vessel (RPV) and primary containment vessel (PCV) leakage/failure through the comparison of pressure, water level, and containment atmosphere monitoring system (CAMS) signatures. The combination of code results and inspections (muon radiography, PCV inspection) has provided a picture of the current status of the debris distribution and plant status. All units present a large relocation of core materials and all of them present ex-vessel debris with Unit 1 and Unit 3 showing evidence of undergoing MCCI. Uncertainties have been identified, in particular on the time and magnitude of events such as corium relocation in the RPV and into the cavity floor and RPV and PCV rupture events. Main uncertainties resulting from the project are the large and continuous MCCI progression predicted by basically all the SA codes and the leak pathways from the RPV to the PCV and the PCV to the reactor building and environment. The BSAF project represents a pioneering exercise that has set the basis and provided lessons learned not only for code improvement but also for the development of new related projects to investigate in detail further aspects of the Fukushima Daiichi accident.
23 September 2021 in Journal of Nuclear Science and Technology
Following the NPP accident, several hundred tons of heat-generating corium and fuel debris have been cooled permanently by millions of m3 of flowing. Knowledge on the interaction with water is crucial for any decommissioning planning. Starting from knowledge on the evolutions of the accident in the three reactor cores and associated fuel debris formations and some additional isotopic and physio-chemical information on debris fragments collected in Fukushima soils, we review the temporal evolution of the chemistry and leached radionuclide contents of the cooling water, comparing measured concentration ratios of the actinides and fission products in the water to reported results of laboratory leaching studies with either spent nuclear fuel or simulated fuel debris. As for spent fuel leaching, the fractions of inventories of 134,137Cs in the cooling water are orders of magnitude larger than that of the actinides. After more than 10 years of fuel debris/water contact, 137Cs release rates have decreased by about a factor of 100. The total release of actinides from the fuel debris is orders of magnitude lower than that of 134,137Cs or of 90Sr. This high stability makes direct disposal of fuel debris in suitable containers after decommissioning a viable option.
25 April 2018 in Journal of Nuclear Science and Technology
Cutting fuel debris (solidified corium) is an important issue for the decommissioning of Fukushima Daiichi Power Station. The main reasons for developing and using suel debris simulants are presented. The relative merits of various types of materials (stainless steel, zircalloy, sintered ceramic, cast-fused zirconia, metal + ceramic, melted inactive simulants, prototypic fuel debris, irradiated fuel debris simulant) that can be used to test debris cutting have been assessed against criteria relevant for the cutting technique itself and also for (radioactive) aerosol and combustible gas generation. Simplified simulants can be used for the development of fuel debris cutting techniques but have limited representativeness so that melted inactive fuel debris simulant must be used to assess the cutting performance. Concerning combustible gas generation, zirconium plates provide an upper bound in term of underwater generation of hydrogen. Finally, for aerosol and dust generation, it appears that non-radioactive simulant cannot correctly represent the aerosol formed during cutting but prototypic fuel debris simulants, using depleted uranium are required. Laser cutting tests have been carried out with several types of simulant materials. Promising results were achieved in term of cutting ability both in air and underwater. Data have also been collected on the released aerosols. Nevertheless, confirmatory experiments with prototypic debris are still needed.
3 September 2020 in Journal of Nuclear Science and Technology
The production and dispersion of contaminated aerosols during the laser cutting of corium can potentially provide useful insights into the dispersion of contamination during the evacuation of damaged reactors during decommissioning. Quantitative assessments of contamination dispersion are fundamental to the development of a safety case for the decommissioning of the Fukushima Daiichi plant. This collaborative work between IRSN, ONET Technologies and CEA, managed by the Mitsubishi Research Institute on behalf of the Japanese Ministry of Economy, Trade and Industry, presents the characterization of aerosols generated during laser cutting of corium simulants both in air and under water. The objective is to obtain quantitative data for risk assessment related to the contamination released and disseminated when implementing this technique, over the next few years, in the process of decommissioning the damaged reactors. This paper presents a part of the results stemming from this project, focused on the characterization of aerosols produced during laser cutting of two representative corium simulants in air and underwater conditions. The experimental configuration also enabled investigation of the production of other material residues such as particle dross and water purity on the particulate composition of the aerosols. Ultimately, the radioisotope concentration distribution in the aerosols are transposed to radioactivity in order to assess the risk to radiation workers during decommissioning.
1 January 2022 in Nuclear Engineering and Design
18 July 2018 in Nuclear Technology
NCNathalie Cassiaut-Louis
+8
Fuel-coolant interaction (FCI) is an important issue for the assessment of severe accident safety for both sodium-cooled fast reactors (SFRs) and pressurized water reactors (PWRs). For the ASTRID SFR demonstrator, FCI is a key phenomenon affecting the relocation of molten fuel in engineered discharge tubes between the core region and the core catcher plenum. FCI controls jet fragmentation and debris bed formation and raises the issue of potentially energetic vapor explosions in the ASTRID lower head. In this frame, experimental data will be necessary to validate SCONE, the fuel-sodium interaction code under development at CEA. For PWRs, one of the configurations of interest lies within the residual case where in-vessel retention would fail. In this case, it is expected that a light metallic layer would be the first to interact with water, before a heavier oxide melt discharge. Here, steam explosion and debris bed formation are the two major points of interest. Based on the experimental expertise gained from the KROTOS facility and its X-ray radioscopic imaging system, new test facilities have been designed to carry out prototypic (depleted uranium–containing) corium interactions with either sodium or water in PLINIUS2, the CEA future large-mass experimental platform dealing with masses above 100 kg. Some test sections have been specially designed to ensure proper visualization of the fuel, liquid coolant, and vapor phases by an improved X-Ray imaging system. This paper presents the future PLINIUS 2 platform as well as the experimental programs foreseen to study both water-corium and sodium-corium interactions.