Song-Charng Kong

Song-Charng Kong

Auto-generated profile, based on publicly available information

Song-Charng Kong

Department of Mechanical Engineering, Texas Tech University , Lubbock, TX 79409

Research Focus & Metrics

Academic Career Length

22Years (2005-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
15 December 2005 in Journal of Engineering for Gas Turbines and Power
Verified
Journal Article
Closed access
PDF file
SKSong-Charng Kong
Song-Charng Kong
YSYong Sun
Yong Sun
RRRolf D. Rietz
Rolf D. Rietz
A detailed chemistry-based CFD model was developed to simulate the diesel spray combustion and emission process. A reaction mechanism of n-heptane is coupled with a reduced NOx mechanism to simulate diesel fuel oxidation and NOx formation. The soot emission process is simulated by a phenomenological soot model that uses a competing formation and oxidation rate formulation. The model is applied to predict the diesel spray lift-off length and its sooting tendency under high temperature and pressure conditions with good agreement with experiments of Sandia. Various nozzle diameters and chamber conditions were investigated. The model successfully predicts that the sooting tendency is reduced as the nozzle diameter is reduced and/or the initial chamber gas temperature is decreased, as observed by the experiments. The model is also applied to simulate diesel engine combustion under premixed charge compression ignition (PCCI) conditions. Trends of heat release rate, NOx, and soot emissions with respect to EGR levels and start-of-injection timings are also well predicted. Both experiments and models reveal that soot emissions peak when the start of injection (SOI) occurs close to TDC. The model indicates that low soot emission at early SOI is due to better oxidation while low soot emission at late SOI is due to less formation. Since NOx emissions decrease monotonically with injection retardation, a late injection scheme can be utilized for simultaneous soot and NOx reduction for the engine conditions investigated in this study.

27 September 2013 in Energy & Fuels
Verified
Journal Article
Closed access
QXQingang Xiong
Qingang Xiong
SASoroush Aramideh
Soroush Aramideh
SKSong-Charng Kong
Song-Charng Kong

1 September 2018 in Energy Conversion and Management
Verified
Journal Article
Closed access
QZQiang Zhang
Qiang Zhang
RORyan M. Ogren
Ryan M. Ogren
SKSong-Charng Kong
Song-Charng Kong

13 September 2016 in ACS Sustainable Chemistry & Engineering
Verified
Journal Article
Closed access
QXQingang Xiong
Qingang Xiong
SKSong-Charng Kong
Song-Charng Kong

1 June 2019 in Computer Physics Communications
Verified
Journal Article
Closed access
XYXiufeng Yang
Xiufeng Yang
SKSong-Charng Kong
Song-Charng Kong

14 September 2017 in Physical Review E
Verified
Journal Article
Open access
PDF file
XYXiufeng Yang
Xiufeng Yang
SKSong-Charng Kong
Song-Charng Kong
The smoothed particle hydrodynamics (SPH) method has been increasingly used for simulating fluid flows; however, its ability to simulate evaporating flow requires significant improvements. This paper proposes an SPH method for evaporating multiphase flows. The present SPH method can simulate the heat and mass transfers across the liquid-gas interfaces. The conservation equations of mass, momentum, and energy were reformulated based on SPH, then were used to govern the fluid flow and heat transfer in both the liquid and gas phases. The continuity equation of the vapor species was employed to simulate the vapor mass fraction in the gas phase. The vapor mass fraction at the interface was predicted by the Clausius-Clapeyron correlation. An evaporation rate was derived to predict the mass transfer from the liquid phase to the gas phase at the interface. Because of the mass transfer across the liquid-gas interface, the mass of an SPH particle was allowed to change. Alternative particle splitting and merging techniques were developed to avoid large mass difference between SPH particles of the same phase. The proposed method was tested by simulating three problems, including the Stefan problem, evaporation of a static drop, and evaporation of a drop impacting a hot surface. For the Stefan problem, the SPH results of the evaporation rate at the interface agreed well with the analytical solution. For drop evaporation, the SPH result was compared with the result predicted by a level-set method from the literature. In the case of drop impact on a hot surface, the evolution of the shape of the drop, temperature, and vapor mass fraction were predicted.