19 July 2023 in Geotechnical Testing Journal
This study presents the results of four years of data collection from a test site that is constructed as part of an actual roadway. The focus of the study was to evaluate the possibility of achieving similar or better performance characteristics from base course sections constructed with reclaimed asphalt pavement (RAP) blends compared to sections with 100 % virgin aggregate (VA). Two base course sections were constructed by blending VA with 20 % RAP and two with 30 % RAP (four RAP-VA sections). Blends were achieved using fine processed RAP with two different average binder contents (4.9 and 5.6 %). Additionally, two sections were constructed with 100 % VA for comparison. During construction, strain gauges were embedded into the asphalt and base course layers. Long-term performance evaluations were monitored based on data from the strain gauges and in situ testing. Falling weight deflectometer and light weight deflectometer tests were used to evaluate modulus values, and the results showed that all sections constructed with RAP-VA blends had equal or greater modulus values than the 100 % VA sections. International roughness index tests coupled with data from strain gauges were used to evaluate deformations. The results showed that three of the four RAP sections had deformations close to or less than 100 % VA sections (desired outcome). The only exception was in the section constructed with 30 % RAP with lower binder content (4.9 %). Findings from this study showed that field evaluations require multiple methods of testing, and modulus-based measurements alone should not be relied on for performance evaluations. This study demonstrated that it is possible to design base course sections with RAP that perform similar to or better than 100 % VA. A proper blend requires the gradation and binder content of RAP to be characterized and the percentage of RAP blended with VA to be determined based on these properties.
3 April 2025 in Transportation Research Record: Journal of the Transportation Research Board
Almost all of the existing testing methods to determine elastic modulus of the soil or aggregate for pavement design involve the application of repetitive loads applied at a single point. This approach falls short of representing the conditions that are observed when the wheel of a vehicle rolls over the surface. This study presents a new methodology, in which light weight deflectometer (LWD) is used to apply three adjacent sequential loads repetitively to replicate a multipoint loading of the surface. The elastic modulus values obtained from these multipoint LWD tests were compared against the repetitive single point LWD test results. The multipoint LWD test elastic modulus values were consistently lower than the values obtained from the single point LWD tests. The single point LWD tests showed an increase in elastic modulus with increased load repetition. The multipoint LWD results did not show an increase in the elastic modulus as a function of repetitive loading. This study showed that damping ratio values provide guidance to explain differences in the elastic modulus with an increased number of load repetitions. In repetitive single point tests, the applied load caused initial compaction, and in multipoint LWD tests, it caused disturbance in the ground. With increased load cycles, the ground reached a stabilized condition in both tests. The methodology presented in this study appeared to minimize the unintended compaction of the ground during the single point LWD tests to determine the elastic modulus.
1 January 2026 in Open Geosciences
The accurate prediction of ultimate settlement is of critical importance for the longevity of structures, as it helps prevent structural damage and functional deterioration. Settlement, a function of the soil’s compression index ( C
c
), is typically determined through oedometer tests. This research seeks to enhance the prediction accuracy of C
c
within a sustainability framework by employing advanced machine learning techniques. A series of soil samples with varying clay contents were synthesized by incorporating bentonite into silt, resulting in nine distinct soil classes ranging from low plasticity silt (ML) to high plasticity clay (CH). Consolidation tests were performed on reconstituted samples subjected to 100 kPa pre-consolidation pressure, revealing significant correlations between the compression index and various physical properties. Leveraging these correlations, a comprehensive dataset was compiled, integrating current experimental data with relevant studies from the literature. The predictive capabilities of several machine learning models, including Support Vector Regression (SVR), Artificial Neural Networks (ANN), Random Forest (RF), and Multiple Regression Analysis (MRA), were evaluated. Among these, the RF model exhibited superior performance, achieving an R 2 of 0.83. The study introduces a novel prediction framework that extends beyond conventional settlement estimation by incorporating a comparative ML-based modeling approach supported by both experimental and literature-based data. Furthermore, the methodology demonstrates its practical value by offering a faster and less resource-dependent alternative to traditional consolidation testing, contributing to sustainability oriented and cost-efficient geotechnical design.
13 April 2026 in Geosynthetics International
Geogrids are widely used to enhance the performance of roadways, especially to improve the conditions associated with soft subgrade. However, the results in the literature do not always show the contribution of the geogrid to improve the elastic modulus of the base course layers consistently. This study demonstrates the use of an existing methodology to overcome such inconsistency. The method used in this study is based on sequentially loading the base course surface with three side-by-side lightweight deflectometers (LWD). The findings of this study showed that such an approach enables us to demonstrate the deterioration of the base course when no geogrid is present and the improved behavior with geogrid placed in between the base course and soft subgrade. The study demonstrates the effective use of KenPave analyses and the results from LWD testing to determine modulus improvement factor (MIF) when geogrids are used. Four different geogrids with different characteristics were evaluated and the determined MIF values ranged between 1.39 and 1.64. The findings were used to develop a relationship between the base course thickness and the allowed maximum stress on the base course for different geogrids, where the applied load is limited to keep the base course elastic.
31 December 2024 in Sakarya University Journal of Science
The bearing capacity of a foundation is crucial for ensuring the stability and safety of structures. However, shallow foundations on unsaturated soils pose challenges due to the complicated behavior of such soils. To address this issue, engineers have developed analytical and numerical methods of analysis, which can be used to determine the bearing capacity of these foundations. This study explored the advantages and disadvantages of these methods, offering a thorough understanding of their role in ensuring the safety and longevity of structures built on unsaturated soil. The analysis in this study was conducted using finite element method simulations on soil sections with varying groundwater levels and degrees of saturation. The results obtained from PLAXIS 2D simulations revealed the effects of fluctuations in groundwater levels and changes in saturation degree on foundation displacements, emphasizing aspects often overlooked in empirical approaches. Under unsaturated conditions, as the degree of saturation decreased, the soil was better able to maintain its structural integrity, resulting in reduced foundation displacements. However, at near-complete saturation (%99), displacements increased significantly, highlighting the risks to foundation stability in soils with high saturation levels, particularly in flood-prone areas. Variability in excess pore water pressure in sections with high saturation indicated potential soil instability under high stresses, impacting structural integrity. Furthermore, finite element analyses showed that classifying soil as drained or undrained impacted foundation displacements. In conclusion, the comprehensive analysis provided by numerical methods emphasized the limitations of empirical approaches and underscored the importance of advanced simulation tools in modern geotechnical practices.