1 September 2017 in Materials Science and Engineering: C
1 March 2011 in International Journal of Sustainable Engineering
This paper presents our research works on developing an evaluation system for remanufacturing. This paper has two objectives. The first objective is to evaluate the product end-of-life (EOL) by integrating an analytical hierarchy process (AHP) with case-based reasoning (CBR). The nearest neighbourhood (NN) algorithm was used to retrieve a past case that is closest to the current case under consideration. The AHP, which allows the pair-wise comparison and consistency judgement, was used to determine the weight in NN. The second objective is to evaluate EOL of parts and components. The integration of an economical cost model and an environmental cost model was used to determine the EOL of parts and components. An example is presented and discussed. The predicted results of the complete method were compared with those of the previous study. The results showed that the integration of the AHP–CBR method has reached a good correspondence with the established methods.
1 December 2016 in Journal of Mechanical Engineering and Sciences
Kenaf fiber has been cultivated as an industrial crop. In this paper, we present the on-going works of an assessment on the mechanical properties of its fiber composites. Tensile, flexural and impact tests were executed on untreated short kenaf fiber reinforced epoxy composites. Its fiber content is varied from 5% up to 20%, and was compared to neat epoxy (NEAT). Using a hand lay-up technique, a mixture of kenaf fiber and epoxy is poured into a mould and left to dry at room temperature for 24 hours. Seven specimens were cut according to ASTM D3039, ASTM D790 and ASTM D256 for the tensile test, flexural test and impact test, respectively. The results showed that the tensile, flexural and impact strengths of the kenaf fiber are lower compared to NEAT. Samples at 5% kenaf fiber content shows the highest tensile strength, flexural strength and impact strength at 27. 1 MPa and 18.2 MPa and 0.56 kJ/m2, respectively. The 5% fiber content was finalized as the fiber content that can be applied in archery.
1 October 2017 in IOP Conference Series: Materials Science and Engineering
Musculoskeletal discomfort (MSD) is very common condition in automotive industry. MSD is affecting the worker's health, well-being and lower down the productivity. Therefore, the main objective of this study was to identify the prevalence of MSD and ergonomics risk factors among the production team members at a selected automotive component manufacturer in Malaysia. MSD data were collected by conducting structure interview with all participants by referring to the Cornell Musculoskeletal Disorder Questionnaire (CMDQ). Those production team members who achieved a total discomfort score for all body regions more than 100 was selected for job task assessment. The physical exposure risk factors of work related musculoskeletal disorders (WMSD) has evaluated by using Quick Exposure Check (QEC) techniques. The results of the study identified the severe MSD associated with production assembly team members. It is expected that the prevalence of MSD for those production assembly team members was lower back (75.4%), upper back (63.2%), right shoulder (61.4%), and right wrist (60%). The QEC analysis discovered that about 70% of job tasks had very high risks for neck posture and 60% had high risks for the back (in moving condition) and shoulder/arm postures. There were 80% of respondents have produced a high score for exposure risk to vibration. As a conclusion, the main implication of the current study is that special attention should be paid to the physical and psychosocial aspects in production team members with musculoskeletal discomfort to improve their safety, health, and well-being, maintain work ability and productivity.
3 June 2019 in Assembly Automation
Purpose: Environmental problems in manufacturing industries are a global issue owing to severe lack fossil resources. In assembly sequence planning (ASP), the research effort mainly aims to improve profit and human-related factors, but it still lacks in the consideration of the environmental issue. This paper aims to present an energy-efficient model for the ASP problem. Design/methodology/approach: The proposed model considered energy utilization during the assembly process, particularly idle energy utilization. The problem was then optimized using moth flame optimization (MFO) and compared with well-established algorithms such as genetic algorithm (GA), particle swarm optimization (PSO) and ant colony optimization (ACO). A computational test was conducted using five assembly problems ranging from 12 to 40 components. Findings: The results of the computational experiments indicated that the proposed model was capable of generating an energy-efficient assembly sequence. At the same time, the results also showed that MFO consistently performed better in terms of the best and mean fitness, with acceptable computational time. Originality/value: This paper proposed a new energy-efficient ASP model that can be a guideline to design assembly station. Furthermore, this is the first attempt to implement MFO for the ASP problem.