27 September 2022 in Advances in Materials Science and Engineering
Drilling is a quite common operation being performed in the manufacturing of components. Instrumental response in drilling is geometrical accuracy and surface integrity of the drilled parts. For the application where geometrical tolerance is very small, an operation is to be carried out very carefully. If not, rejection of drilled samples will be higher and consequently production loss will be higher. The use of prediction model in this scenario is much more appropriate and cost-effective. This research aimed to apply extreme gradient boosting (XGBoost) regressor to develop a drilling prediction model. Drilling experiments were conducted after developing design of experiments with twenty-seven unique sets. Experimental data analysis was then carried out on experimental data sets that have features such as speed, feed, angle, hole length, and surface roughness. After correlation analysis, the k-fold cross validation method was applied for parameterisation. Hyperparameters estimated from the k-fold cross validation were then applied to train and test the XGBoost regressor-based machine learning (ML) model. It is concluded from the model evaluation metric (R2) that the XGBoost regressor model has resulted 0.89 before tuning and 0.94 after tuning of the model, which is higher than the polynomial regressor and support vector regressor.
11 February 2022 in IEEE Access
Teaching learning-based optimization (TLBO) is a popular algorithm used to solve various optimization problems. Nevertheless, conventional TLBO and some improved variants tends to suffer with premature convergence due to rapid loss of population diversity, especially when handling the challenging optimization problems. Furthermore, it is not practical to tackle real-world multiobjective problems using prior approach given the frequent changes of customers’ requirements. Motivated by these challenges, an improved variant known as Modified Multi-objective Teaching Learning Based Optimization-Refined Learning Scheme (MMTLBO-RLS) was proposed as a posterior approach to solve challenging multiobjective optimization problems, including the prediction of optimum turning parameters to machine Polyether ether ketone material (PEEK). Substantial modifications were introduced for teacher and learner phases of MMTLBO-RLS to achieve better balancing of exploration and exploitation searches without incurring excessive computational cost. For modified teacher phase of MMTLBO-RLS, each learner was guided by a unique teacher solution and unique mean position to perform searching with better diversity. Meanwhile, two new learning strategies are incorporated into the modified learner phase of MMTLBO-RLS, enabling all learners to enhance their knowledge more efficiently based on their learning preferences. A systematic approach was followed to develop modelling equations required for optimization. The developed algorithm was then employed in single objective optimization as well as multiobjective optimization to cater its performances in any real-world environment. The prediction model reports that surface roughness of $1.1042~\mu m$ and material removal rate of 22.8991 cm 3 /minute can be achieved. The predicted results differ from validation results by less than 2.69% in any case of optimization. A benchmarking on the performance of MMTLBO-RLS in solving CEC 2009 multiobjective benchmark functions was further carried out with other seven meta-heuristic algorithms. The superior performance of MMTLBO-RLS proves that it is not only suitable to be used in industries to produce the parts of PEEK with supportive quality and quantity, but it is also able to solve other multiobjective optimization problems with competitive performances.
21 April 2022 in Mathematical Problems in Engineering
This research is done to determine the optimum parameters to drill polytetrafluoroethylene (PTFE) and to investigate the effect of two-tier modeling for enhanced response in optimization. RSM model was done with L27 experimental design, considering speed (N), feed (f), and tool point angle (Ɵ). RSM data were further trained and tested using the Adaptive Neuro-Fuzzy Inference System (ANFIS), and β coefficient values were restructured to form revised RSM model. Both nonrevised RSM model and revised RSM model were used in Genetic Algorithm to locate the minimum surface roughness. ANFIS revised RSM model deviates from the experimental results by 2.6 and 2.86 for dry and wet condition; meanwhile, nonrevised RSM model deviates by 4.76 and 4.94, respectively. The research concludes that two-tier modeling using RSM and ANFIS is better. Spindle speed of 1656rpm, feed rate of 0.05mm/min, and point angle of 100° are the optimum conditions to drill PTFE material where the best surface quality of 0.68μm at wet drilling can be achieved.