Tomasz Janiak

Tomasz Janiak

Auto-generated profile, based on publicly available information

Tomasz Janiak

Radioisotope Centre POLATOM, National Centre for Nuclear Research , Andrzeja Sołtana 7 St. , Otwock-Świerk , Poland

Research Focus & Metrics

Academic Career Length

16Years (2011-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
15 February 2015 in Journal of Radioanalytical and Nuclear Chemistry
Verified
Journal Article
Open access
PDF file
ASA. Stolarz
A. Stolarz
JKJ. A. Kowalska
J. A. Kowalska
PJP. Jasiński
P. Jasiński
TJT. Janiak
T. Janiak
JSJ. Samorajczyk
J. Samorajczyk
Targets required to determine the parameters of the 100Mo(p,xn)99mTc reaction and to estimate the yield of the 99mTc production were prepared starting with powder material. Material, melted with electron beam gun into solid bead, was reshaped into foil mechanically. Targets were prepared by powder melting and hot flattening of the droplet followed by cold rolling. Procedure allowed preparation of thick (in the range of hundreds of microns) and thin (down to 250 nm) foils.

1 June 2017 in Applied Radiation and Isotopes
Verified
Journal Article
Closed access
ICIzabela Cieszykowska
Izabela Cieszykowska
TJTomasz Janiak
Tomasz Janiak
TBTadeusz Barcikowski
Tadeusz Barcikowski
MMMieczysław Mielcarski
Mieczysław Mielcarski
RMRenata Mikołajczak
Renata Mikołajczak
LKLukasz Kurpaska
Lukasz Kurpaska

20 December 2021 in Journal of Radioanalytical and Nuclear Chemistry
Verified
Journal Article
Open access
PDF file
ICIzabela Cieszykowska
Izabela Cieszykowska
KJKatarzyna Jerzyk
Katarzyna Jerzyk
MŻMałgorzata Żółtowska
Małgorzata Żółtowska
TJTomasz Janiak
Tomasz Janiak
GBGrażyna Birnbaum
Grażyna Birnbaum
Electrochemical dissolution of pressed into discs and sintered metallic molybdenum powder with the mass of 712 ± 10 mg (n = 15) in potassium hydroxide solution was studied in detail. The technique was considered to apply for dissolution of irradiated100Mo target in the99mTc production. The effect of various parameters, e.g., the concentration of the electrolyte solution, temperature, current density, and surface area of the platinum cathode, was investigated. The shortest time for total dissolution of molybdenum target was 70 min. This result was achieved using an electrolyte solution of 5 M KOH, temperature 55 °C and the current density of 365 mA/cm2.

1 September 2011 in Applied Radiation and Isotopes
Verified
Journal Article
Closed access
ICIzabela Cieszykowska
Izabela Cieszykowska
MŻMaŁgorzata ŻóŁtowska
MaŁgorzata ŻóŁtowska
PZPiotr Zachariasz
Piotr Zachariasz
APAndrzej Piasecki
Andrzej Piasecki
TJTomasz Janiak
Tomasz Janiak
MMMieczysŁaw Mielcarski
MieczysŁaw Mielcarski

21 October 2025 in Nukleonika
Verified
Journal Article
Open access
PDF file
TZTobiasz Zawistowski
Tobiasz Zawistowski
SWSławomir Wronka
Sławomir Wronka
PAPrzemysław Adrich
Przemysław Adrich
MCMariusz Chabera
Mariusz Chabera
ICIzabela Cieszykowska
Izabela Cieszykowska
MMMichał Matusiak
Michał Matusiak
The authors present the first observation of the production of 99 Mo using a direct electron beam obtained from an electron linear accelerator in the 10–20 MeV energy region. Three disks of natural molybdenum, with diameters of 20 mm and thicknesses of 0.12 mm, 0.33 mm, and 1.13 mm, respectively, were irradiated by an electron beam with the most probable energies of 12.6 MeV and 15.6 MeV. The highest observed activity in the experiment was equal to 646 ± 30 kBq, which is in good agreement with Geant4 simulations. Although 99 Mo production is significantly higher with gamma beams, the presented results contribute to the analysis of an interesting electrodisintegration process.