David E. James

David E. James

Auto-generated profile, based on publicly available information

David E. James

Department of Civil and Environmental Engineering and Construction, University of Nevada, Las Vegas, NV, USA

Research Focus & Metrics

Academic Career Length

33Years (1994-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
13 July 2023 in Remote Sensing
Verified
Journal Article
Open access
PDF file
GAGodson Ebenezer Adjovu
Godson Ebenezer Adjovu
Haroon StephenHaroon Stephen
Haroon Stephen
DJDavid James
David James
Sajjad AhmadSajjad Ahmad
Sajjad Ahmad
This study provides a comprehensive review of the efforts utilized in the measurement of water quality parameters (WQPs) with a focus on total dissolved solids (TDS) and total suspended solids (TSS). The current method used in the measurement of TDS and TSS includes conventional field and gravimetric approaches. These methods are limited due to the associated cost and labor, and limited spatial coverages. Remote Sensing (RS) applications have, however, been used over the past few decades as an alternative to overcome these limitations. Although they also present underlying atmospheric interferences in images, radiometric and spectral resolution issues. Studies of these WQPs with RS, therefore, require the knowledge and utilization of the best mechanisms. The use of RS for retrieval of TDS, TSS, and their forms has been explored in many studies using images from airborne sensors onboard unmanned aerial vehicles (UAVs) and satellite sensors such as those onboard the Landsat, Sentinel-2, Aqua, and Terra platforms. The images and their spectral properties serve as inputs for deep learning analysis and statistical, and machine learning models. Methods used to retrieve these WQP measurements are dependent on the optical properties of the inland water bodies. While TSS is an optically active parameter, TDS is optically inactive with a low signal–noise ratio. The detection of TDS in the visible, near-infrared, and infrared bands is due to some process that (usually) co-occurs with changes in the TDS that is affecting a WQP that is optically active. This study revealed significant improvements in incorporating RS and conventional approaches in estimating WQPs. The findings reveal that improved spatiotemporal resolution has the potential to effectively detect changes in the WQPs. For effective monitoring of TDS and TSS using RS, we recommend employing atmospheric correction mechanisms to reduce image atmospheric interference, exploration of the fusion of optical and microwave bands, high-resolution hyperspectral images, utilization of ML and deep learning models, calibration and validation using observed data measured from conventional methods. Further studies could focus on the development of new technology and sensors using UAVs and satellite images to produce real-time in situ monitoring of TDS and TSS. The findings presented in this review aid in consolidating understanding and advancement of TDS and TSS measurements in a single repository thereby offering stakeholders, researchers, decision-makers, and regulatory bodies a go-to information resource to enhance their monitoring efforts and mitigation of water quality impairments.

4 April 2023 in Remote Sensing
Verified
Journal Article
Open access
PDF file
GAGodson Ebenezer Adjovu
Godson Ebenezer Adjovu
Haroon StephenHaroon Stephen
Haroon Stephen
DJDavid James
David James
Sajjad AhmadSajjad Ahmad
Sajjad Ahmad
This study provides an overview of the techniques, shortcomings, and strengths of remote sensing (RS) applications in the effective retrieval and monitoring of water quality parameters (WQPs) such as chlorophyll-a concentration, turbidity, total suspended solids, colored dissolved organic matter, total dissolved solids among others. To be effectively retrieved by RS, these WQPs are categorized as optically active or inactive based on their influence on the optical characteristics measured by RS sensors. RS applications offer the opportunity for decisionmakers to quantify and monitor WQPs on a spatiotemporal scale effectively. The use of RS for water quality monitoring has been explored in many studies using empirical, analytical, semi-empirical, and machine-learning algorithms. RS spectral signatures have been applied for the estimation of WQPs using two categories of RS, namely, microwave and optical sensors. Optical RS, which has been heavily applied in the estimation of WQPs, is further grouped as spaceborne and airborne sensors based on the platform they are on board. The choice of a particular sensor to be used in any RS application depends on various factors including cost, and spatial, spectral, and temporal resolutions of the images. Some of the known satellite sensors used in the literature and reviewed in this paper include the Multispectral Instrument aboard Sentinel-2A/B, Moderate Resolution Imaging Spectroradiometer, Landsat Thematic Mapper, Enhanced Thematic Mapper, and Operational Land Imager.

14 April 2019 in Catalysts
Verified
Journal Article
Open access
PDF file
SMSoroosh Mortazavian
Soroosh Mortazavian
ASAli Saber
Ali Saber
DJDavid E. James
David E. James
Textile industries produce copious amounts of colored wastewater some of which are toxic to humans and aquatic biota. This study investigates optimization of a bench-scale UV-C photocatalytic process using a TiO2 catalyst suspension for degradation of two textile dyes, Acid Blue 113 (AB 113) and Acid Red 88 (AR 88). From preliminary experiments, appropriate ranges for experimental factors including reaction time, solution pH, initial dye concentration and catalyst dose, were determined for each dye. Response surface methodology (RSM) using a cubic IV optimal design was then used to design the experiments and optimize the process. Analysis of variance (ANOVA) was employed to determine significance of experimental factors and their interactions. Results revealed that among the studied factors, solution pH and initial dye concentration had the strongest effects on degradation rates of AB 113 and AR 88, respectively. Least-squares cubic regression models were generated by step-wise elimination of non-significant (p-value > 0.05) terms from the proposed model. Under optimum treatment conditions, removal efficiencies reached 98.7% for AB 113 and 99.6% for AR 88. Kinetic studies showed that a first-order kinetic model could best describe degradation data for both dyes, with degradation rate constants of k1, AB 113 = 0.048 min−1 and k1, AR 88 = 0.059 min−1.

1 July 2001 in Earth and Planetary Science Letters
Verified
Journal Article
Closed access
LWLianxing Wen
Lianxing Wen
PSPaul Silver
Paul Silver
DJDavid James
David James
RKRandy Kuehnel
Randy Kuehnel

3 January 2004 in Geochemistry, Geophysics, Geosystems
Verified
Journal Article
Open access
PDF file
DJD. E. James
D. E. James
FBF. R. Boyd
F. R. Boyd
DSD. Schutt
D. Schutt
DBDavid R. R Bell
David R. R Bell
RCR. W. Carlson
R. W. Carlson
We impose geologic constraints on seismic three‐dimensional (3‐D) images of the upper mantle beneath southern Africa by calculating seismic velocities and rock densities from approximately 120 geothermobarometrically calibrated mantle xenoliths from the Archean Kaapvaal craton and adjacent Proterozoic mobile belts. Velocity and density estimates are based on the elastic and thermal moduli of constituent minerals under equilibrium P‐T conditions at the mantle source. The largest sources of error in the velocity estimates derive from inaccurate thermo‐barometry and, to a lesser extent, from uncertainties in the elastic constants of the constituent minerals. Results are consistent with tomographic evidence that cratonic mantle is higher in velocity by 0.5–1.5% and lower in density by about 1% relative to off‐craton Proterozoic samples at comparable depths. Seismic velocity variations between cratonic and noncratonic xenoliths are controlled dominantly by differences in calculated temperatures, with compositional effects secondary. Different temperature profiles between cratonic and noncratonic regions have a relatively minor influence on density, where composition remains the dominant control. Low‐T cratonic xenoliths exhibit a positive velocity‐depth curve, rising from about 8.13 km/s at uppermost mantle depths to about 8.25 km/s at 180‐km depth. S velocities decrease slightly over the same depth interval, from about 4.7 km/s in the uppermost mantle to 4.65 km/s at 180‐km depth. P and S velocities for high‐T lherzolites are highly scattered, ranging from highs close to those of the low‐T xenoliths to lows of 8.05 km/s and 4.5 km/s at depths in excess of 200 km. These low velocities, while not asthenospheric, are inconsistent with seismic tomographic images that indicate high velocity root material extending to depths of at least 250 km. One plausible explanation is that high temperatures determined for the high‐T xenoliths are a nonequilibrium consequence of relatively recent thermal perturbation and compositional modification associated with emplacement of kimberlitic fluids into the deep tectospheric root. Seismic velocities and densities for cratonic xenoliths differ significantly from those predicted for both primitive mantle peridotite and mantle eclogite. A model primitive mantle under cratonic P‐T conditions exhibits velocities about 1% lower for P and about 1.5% lower for S, a consequence of a more fertile composition and different modal composition. Primitive mantle is also about 2% more dense at 150‐km depth than low‐T garnet lherzolite at cratonic P‐T conditions. Similar calculations based on an oceanic geotherm are consistent with the isopycnic hypothesis of comparable density columns beneath oceanic and cratonic regions. Calculations for a hypothetical “cratonic” eclogite (50:50 garnet/omphacite) with an assumed cratonic geotherm produce extremely high VP and VS (8.68 km/s and 4.84 km/s, respectively, at 150 km depth) as well as high density (∼3.54 gm/cc). The very high velocity of eclogite should render it seismically conspicuous in the cratonic mantle if present as large volume blocks or slabs. We discuss how the seismic velocity data we have compiled in this paper from both xenoliths and generic petrologic models of the upper mantle differ from commonly used standard earth models IASPEI and PREM.