The present research intends to design an efficient receiver for solar thermal applications with a solar dish concentrator system. Thermal and dynamic analysis is carried out for different convolutions of a spiral coil, and experiments are performed for testing the modified absorber. Experimental results are validated for the spiral absorber with numerical results. Three receivers of different numbers of convolutions are analyzed, and simulation steps are performed for these receivers to make improvements in the system efficiency. Finally, 5 convolutions of a spiral coil tubular absorber are taken for the modified design of the system. Absorber position for every spiral convolution is kept at the focus of the concentrated solar dish collector to achieve maximum efficiency. Material used for the reflective surface is anodized aluminum and copper for the absorber. The diameter of the aperture for the parabolic dish collector is 1.4 m. The maximum absorber temperature for May month comes out to be 296°C, and the maximum working fluid outlet temperature is found to be 294.2°C which is near to simulating temperature of 289.59°C and 288.15°C, respectively. This innovative design of the absorber consists of a feature of a 5 mm extension to the spiral tube at the exit and entry; hence, the turbulence effect could be overcome. Experimental thermal efficiency was found the highest (i.e., ) for May. This work emphasizes on improving thermal performance by obtaining optimum absorber size using convolution strategy. Investigation of 5 convolutions of spiral coil tubular absorber with extended ends for obtaining optimum performance than existing work is the superiority of this work.
Large wind turbines of the horizontal axis are commonly used to gather wind energy; however, their performance is found to be constrained in conditions of erratic and low-speed wind flow. In contrast, low wind conditions—which are typically present in dense urban areas—are found to favour vertical axis wind turbines (VAWT). These turbines have a simple design, are inexpensive and quiet, and are discovered to be better in low wind situations. In this research, we have chosen wind tree applications to absorb the most available wind energy. The new Aeroleaf Savonius Wind Turbine was developed numerically and a computational fluid dynamics simulation was performed on this new type of Savonius tree to predict its performance. The results indicated that the system could accept wind from any direction and could start rotating as soon as the site had a cut in wind speed of 3.3 m/s. The rotor speed increased by 10.4% from 5.5 to 6.3 m/s wind speed at 0.45 tip speed ratio. The tip speed ratio is 0.52 at the site’s high wind speed, and under these circumstances, the maximum Cp is 12.9%. The turbine was able to produce superior performance coefficients, according to the results.
Solar still is best choice of utilizing freely available solar thermal energy to purify/desalinate muddy water. The driving force for this work is the inadequate availability of clean fresh water sources and the plenty of contaminated water available for probable conversion into potable water. Among various designs available, double basin passive solar still looks attractive for thermal applications in water prone and remote areas. This work presents experimental characterization of double slope solar still using phase change materials. This work aims to improve the performance (productivity of fresh water) using Mg2SO4.7H2O as phase change material (PCM). Different tests were conducted for varying mass of the PCM. For experimentation, two identical double slope solar stills (basin area of 0.5×0.5 m2) were designed, fabricated and tested for freshwater productivity. One is solar still (without PCM) and second with phase change material. A water depth of 5 cm was constant throughout the experimentation under climate conditions of Jabalpur (23° 10' N, 79° 59'E), Madhya Pradesh India. The results obtained indicate that daily distillate for solar still with Magnesium sulfate heptahydrate is higher as compared to solar still without PCM. The convective heat transfer coefficient increases during the discharging period of PCM The daily freshwater productivity of 1400, 1420 & 1400 ml/m2/day for solar still (without Mg2SO4.7H2O), while 1800, 1900 & 1960 ml/m2day for the solar still (with PCM) were recorded with addition of 0.5, 0.75 and 1kg of Mg2SO4.7H2O respectively. The overall thermal efficiency of the solar still with PCM was observed to be 64%, and for a solar still without the PCM, it was 47% while the other conditions kept constant.
1 June 2019 in Proceedings of the Institution of Civil Engineers - Municipal Engineer
The rapid population growth and an increase in the living standard of inhabitants have caused insurmountable problems to the municipal solid waste management (MSWM) of Bhopal city. The city generates approximately 800 t/d of municipal solid waste (MSW) and it is estimated to increase to approximately 2735 t/d by the year 2035. This paper presents an overview of the existing MSWM practices in Bhopal city and suggests a roadmap to overcome the shortcoming. Some of the major drawbacks are: an absence of an engineering landfill, improper management of MSW, lack of suitable facilities (equipment and infrastructure) and funds. This has caused contamination of different environmental slots, including soil, groundwater/surface water and air leading to unhealthy dwelling conditions. Physical and chemical analyses of waste indicates a high concentration (45%) of biodegradable waste, low calorific value (378–4680 kcal/kg) and high moisture content (>30%) of MSW. Overall, 15% of the waste was found suitable for electricity generation. A roadmap for better management is proposed that includes segregation at source, recycling and reuse for sustainable management of MSW as per provisions made in solid waste management rules, 2016. This roadmap will definitely enhance the awareness campaign ‘Team Up to Clean Up’ launched by Bhopal Municipal Corporation in 2014.