Efficiency from hole-selective contacts: Perovskite/silicon tandem solar cells must stabilize a perovskite material with a wide bandgap and also maintain efficient charge carrier transport. Al-Ashouri et al. stabilized a perovskite with a 1.68–electron volt bandgap with a self-assembled monolayer that acted as an efficient hole-selective contact that minimizes nonradiative carrier recombination. In air without encapsulation, a tandem silicon cell retained 95% of its initial power conversion efficiency of 29% after 300 hours of operation. Science , this issue p. 1300
Improved stability and efficiency of two-terminal monolithic perovskite-silicon tandem solar cells will require reductions in recombination losses. By combining a triple-halide perovskite (1.68 electron volt bandgap) with a piperazinium iodide interfacial modification, we improved the band alignment, reduced nonradiative recombination losses, and enhanced charge extraction at the electron-selective contact. Solar cells showed open-circuit voltages of up to 1.28 volts in p-i-n single junctions and 2.00 volts in perovskite-silicon tandem solar cells. The tandem cells achieve certified power conversion efficiencies of up to 32.5%.
Perovskite–silicon tandem solar cells offer the possibility of overcoming the power conversion efficiency limit of conventional silicon solar cells. Various textured tandem devices have been presented aiming at improved optical performance, but optimizing film growth on surface-textured wafers remains challenging. Here we present perovskite–silicon tandem solar cells with periodic nanotextures that offer various advantages without compromising the material quality of solution-processed perovskite layers. We show a reduction in reflection losses in comparison to planar tandems, with the new devices being less sensitive to deviations from optimum layer thicknesses. The nanotextures also enable a greatly increased fabrication yield from 50% to 95%. Moreover, the open-circuit voltage is improved by 15 mV due to the enhanced optoelectronic properties of the perovskite top cell. Our optically advanced rear reflector with a dielectric buffer layer results in reduced parasitic absorption at near-infrared wavelengths. As a result, we demonstrate a certified power conversion efficiency of 29.80%.
Achieving high solar-to-hydrogen (STH) efficiency concomitant with long-term durability using low-cost, scalable photo-absorbers is a long-standing challenge. Here we report the design and fabrication of a conductive adhesive-barrier (CAB) that translates >99% of photoelectric power to chemical reactions. The CAB enables halide perovskite-based photoelectrochemical cells with two different architectures that exhibit record STH efficiencies. The first, a co-planar photocathode-photoanode architecture, achieved an STH efficiency of 13.4% and 16.3 h to t60, solely limited by the hygroscopic hole transport layer in the n-i-p device. The second was formed using a monolithic stacked silicon-perovskite tandem, with a peak STH efficiency of 20.8% and 102 h of continuous operation before t60 under AM 1.5G illumination. These advances will lead to efficient, durable, and low-cost solar-driven water-splitting technology with multifunctional barriers.
Monolithic perovskite/silicon tandem solar cells recently surpass the efficiency of silicon single‐junction solar cells. Most tandem cells utilize >250 μm thick, planarized float‐zone (FZ) silicon, which is not compatible with commercial production using <200 μm thick Czochralski (CZ) silicon. The perovskite/silicon tandem cells based on industrially relevant 100 μm thick CZ‐silicon without mechanical planarization are demonstrated. The best power conversion efficiency (PCE) of 27.9% is only marginally below the 28.2% reference value obtained on the commonly used front‐side polished FZ‐Si, which are about three times thicker. With both wafer types showing the same median PCE of 27.8%, the thin CZ‐Si‐based devices are preferred for economic reasons. To investigate perspectives for improved current matching and, therefore, further efficiency improvement, optical simulations with planar and textured silicon have been conducted: the perovskite's bandgap needs to be increased by ≈0.02 eV when reducing the silicon thickness from 280 to 100 μm. The need for bandgap enlargement has a strong impact on future tandem developments ensuring photostable compositions with lossless interfaces at bandgaps around or above 1.7 eV.