M. Yu. Simonov

M. Yu. Simonov

Auto-generated profile, based on publicly available information

M. Yu. Simonov

Perm National Research Polytechnic University, Perm, Russia

Research Focus & Metrics

Academic Career Length

10Years (2017-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
6 April 2021 in Metals
Verified
Journal Article
Open access
PDF file
DPDmitrii Panov
Dmitrii Panov
EKEgor Kudryavtsev
Egor Kudryavtsev
RCRuslan Chernichenko
Ruslan Chernichenko
ASAleksandr Smirnov
Aleksandr Smirnov
Nikita StepanovNikita Stepanov
Nikita Stepanov
GSGennady Salishchev
Gennady Salishchev
The martensite-to-austenite reversion mechanisms under continuous heating and annealing of metastable austenitic stainless steel subjected to cold swaging were studied. The reversion-temperature-time diagram was constructed using high-resolution dilatometry. The diagram revealed a sequence of martensitic and diffusional reversion and recrystallization. Martensitic and diffusional reversion might be separated by using the heating rate of >10 °C/s. The reversion started via the martensitic mechanism, and the diffusional mechanism developed during subsequent heating. However, both mechanisms enhance simultaneously during continuous heating at slow heating rates (<10 °C/s). At higher temperatures, recrystallization occurred. Post-mortem microstructure analysis has allowed classifying the reverse annealing modes into low- (500–650 °C), medium- (~700 °C), and high-temperature (~800 °C) regimes. During low-temperature annealing, the development of the phase reversion, recovery, recrystallization, and carbide precipitation was characterized by both a high amount of new austenite grains and restriction of their growth that resulted in the formation of an ultrafine grain structure with an average grain size of 100–200 nm. Medium-temperature annealing was associated with the formation of almost a fully recrystallized austenitic structure, but the lamellar regions were still detected. Austenitic grain growth and dissolution of carbide particles were enhanced during high-temperature annealing.

26 June 2019 in Materials
Verified
Journal Article
Open access
PDF file
DPDmitrii Panov
Dmitrii Panov
APAlexey Pertsev
Alexey Pertsev
Alexander SmirnovAlexander Smirnov
Alexander Smirnov
VKVladislav Khotinov
Vladislav Khotinov
YSYuri Simonov
Yuri Simonov
The article presents the influence of structure formation on the properties of 321 metastable austenitic stainless steel in the process of cold radial forging (CRF). The steel under study after austenitization was subjected to CRF at room temperature with degrees of true strain (e) 0.26, 0.56, 1.00, 1.71 and 2.14. It has been shown that structure formation of the studied steel during CRF consists of three stages: formation of the lamellar structure of austenite, formation of the trapezoidal structure, and formation of the equiaxial grain structure. The kinetics of the strain-induced α′-martensitic transformation is related to the stages of structure evolution. Hardness, ultimate tensile strength and yield strength uniformly increase in all stages of structure formation with a significant decrease of elongation to fracture during the first stage of structure formation while the value of elongation to fracture remains constant in the subsequent stages of deformation. Impact strength of fatigue cracked specimens (KCT) decreases sharply at the first stage of structure formation and smoothly increases at the second and third stages. However, the impact strength of V-notch specimens (KCV) continuously decreases when deformation degree increases in the overall investigated deformation range.

1 January 2020 in Metal Science and Heat Treatment
Verified
Journal Article
Closed access
PDF file
MSM. Yu. Simonov
M. Yu. Simonov
YSYu. N. Simonov
Yu. N. Simonov
GSG. S. Shaimanov
G. S. Shaimanov

1 January 2018 in Physics of Metals and Metallography
Verified
Journal Article
Closed access
PDF file
MSM. Yu. Simonov
M. Yu. Simonov
YSYu. N. Simonov
Yu. N. Simonov
GSG. S. Shaimanov
G. S. Shaimanov
The structure, dynamic cracking resistance, and micromechanisms of crack growth in initially highly tempered pipe billets made of structural carbon steel are studied after thermomechanical treatment,...

15 December 2017 in Metal Working and Material Science
Verified
Journal Article
Closed access
DPDmitrii Panov
Dmitrii Panov
TBTatyana Barsukova
Tatyana Barsukova
Alexander SmirnovAlexander Smirnov
Alexander Smirnov
EOEvgeniya Orlova
Evgeniya Orlova
YSYuriy Simonov
Yuriy Simonov

17 June 2022 in Physical Mesomechanics
Verified
Journal Article
Closed access
PDF file
MSM. Yu. Simonov
M. Yu. Simonov
ONO. B. Naimark
O. B. Naimark
YSYu. N. Simonov
Yu. N. Simonov
GSG. S. Shaimanov
G. S. Shaimanov
DLD. R. Ledon
D. R. Ledon
Systematic microhardness measurements were performed to assess the shape and size of plastic deformation zones formed under the fracture surface in quenched and tempered steel 25 during dynamic testing. It was found that as the tempering temperature of the steel decreases, the size of the plastic deformation zone in the region of dynamic crack initiation decreases, and the dynamic crack becomes flatter. The stress and strain fields at the crack front in high-tempered steel 25 under dynamic loading were modeled by finite element simulations. The simulation results revealed a multistage evolution of the stress and strain fields in tests for dynamic crack resistance. The experimental results on microhardness distribution in the plastic deformation zone under the fracture surface and strain distributions during dynamic crack propagation showed good qualitative agreement with the simulation results. Electron microscopic examination of the starting region of the plastic deformation zone and the hammer impact region revealed adiabatic shear bands in the subsurface of the fractured specimen. Tracks of composition contrast observed along the band boundaries indicate the mass transfer of carbon. Simultaneous studies of the structure and fracture surface in the impact region showed that the dynamic crack propagates mainly along the boundaries of structural elements that induce adiabatic shear, resulting in the formation of characteristic grooves on the fracture surface.