Shouyi Sun

Shouyi Sun

Auto-generated profile, based on publicly available information

Shouyi Sun

State Key Laboratory of Clean and Efficient Turbomachinery Power Equipment, School of Mechanies, Civil Engineering and Architecture

Research Focus & Metrics

Academic Career Length

3Years (2024-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
14 June 2024 in ACS Applied Nano Materials
Verified
Journal Article
Closed access
SSShouyi Sun
Shouyi Sun
XMXiaoyang Ma
Xiaoyang Ma
WSWei Song
Wei Song
Zhengmao DingZhengmao Ding
Zhengmao Ding
Jinjin LiJinjin Li
Jinjin Li

5 August 2025 in ACS Applied Materials & Interfaces
Verified
Journal Article
Closed access
MLMaohua Li
Maohua Li
CGChenxi Guan
Chenxi Guan
YZYaolong Zhi
Yaolong Zhi
JLJindong Li
Jindong Li
SSShouyi Sun
Shouyi Sun
JPJunxia Peng
Junxia Peng

5 November 2025 in International Journal of Plasticity
Verified
Journal Article
Closed access
HLH.T. Li
H.T. Li
XWX.M. Wang
X.M. Wang
HCH. Cheng
H. Cheng
ZDZ.L. Ding
Z.L. Ding
SSS.Y. Sun
S.Y. Sun
YWY. Wang
Y. Wang

12 September 2025 in International Journal of Fatigue
Verified
Journal Article
Closed access
WGWenbo Gao
Wenbo Gao
SSShouyi Sun
Shouyi Sun
XWXinmei Wang
Xinmei Wang

30 June 2026 in SSRN Electronic Journal
Verified
Preprint
Open access
ZDZhiLin Ding
ZhiLin Ding
XWX.M. Wang
X.M. Wang
WHWei Huang
Wei Huang
SSS.Y. Sun
S.Y. Sun
WYW.Z. Yang
W.Z. Yang
ZYZ.F. Yue
Z.F. Yue
Internally cooled thin walled turbine blades are subjected to radial temperature gradients during service. Asymmetric environments are also imposed on the outer diameter (OD) and inner diameter (ID) sides. The baseline creep behavior of continuous single crystal thin-wall structures is investigated under these conditions. The [001] oriented hollow tube specimens are directly cast from a third-generation Ni-based single crystal superalloy. Wall thicknesses of 0.8 mm and 0.5 mm are used. Temperature gradient creep tests are conducted at an OD side temperature of 980 °C. A through thickness temperature gradient of approximately 10⁵ K/m is imposed. Isothermal creep specimens with the same OD side temperature are used as controls. The through thickness temperature field is reconstructed using OD side temperature calibration, cooling-air boundary conditions, and fluid–solid heat-transfer analysis. The fracture and damage behavior is systematically characterized using fracture morphology, OD side and ID side surface damage, oxidation and γ′ degradation, void area fraction, γ/γ′ rafting morphology, EDS elemental redistribution, and crystal-slip analysis coupled with the temperature field. The creep rupture lives of the 0.8 mm and 0.5 mm tube specimens are increased by 6.80% and 21.71%, respectively, by the internally cooled temperature gradient at 366 MPa. The wall-thickness debit is reduced from 16.02% under the non-gradient condition to 4.29% under the thermal gradient condition. The creep life of the 0.8 mm thermal gradient specimen is reduced by 52.15% when the applied stress is increased from 366 MPa to 585 MPa. The damage state is clearly partitioned along the wall thickness. Stronger environmental degradation is observed on the ID side. Higher void accumulation is detected on the hot OD side. More pronounced N-type γ/γ′ rafting is also observed on the hot OD side. More severe accumulated creep damage is identified on the hot OD side. The maximum resolved shear stress is shown by crystal-slip analysis to increase toward the cooler ID side. The thermally activated creep rate and accumulated damage are still concentrated on the hot OD side. The wall-thickness debit of internally cooled single-crystal thin-wall tubes under a temperature gradient cannot be directly extrapolated from isothermal thin-wall creep behavior. This response should be understood as a combined thermal, mechanical, and environmental effect. The response is mainly controlled by the hot OD side.