Olivier Le Neel

Olivier Le Neel

Auto-generated profile, based on publicly available information

Olivier Le Neel

STMicroelectronics Pte Ltd., Singapore 569508, Singapore

Research Focus & Metrics

Academic Career Length

17Years (2010-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
17 January 2019 in Sensors
Verified
Journal Article
Open access
ALAyoub Lahlalia
Ayoub Lahlalia
ONOlivier Le Neel
Olivier Le Neel
RSRavi Shankar
Ravi Shankar
Siegfried SelberherrSiegfried Selberherr
Siegfried Selberherr
Lado FilipovicLado Filipovic
Lado Filipovic
Semiconducting metal oxide (SMO) gas sensors were designed, fabricated, and characterized in terms of their sensing capability and the thermo-mechanical behavior of the micro-hotplate. The sensors demonstrate high sensitivity at low concentrations of volatile organic compounds (VOCs) at a low power consumption of 10.5 mW. In addition, the sensors realize fast response and recovery times of 20 s and 2.3 min, respectively. To further improve the baseline stability and sensing response characteristics at low power consumption, a novel sensor is conceived of and proposed. Tantalum aluminum (TaAl) is used as a microheater, whereas Pt-doped SnO2 is used as a thin film sensing layer. Both layers were deposited on top of a porous silicon nitride membrane. In this paper, two designs are characterized by simulations and experimental measurements, and the results are comparatively reported. Simultaneously, the impact of a heat pulsing mode and rubber smartphone cases on the sensing performance of the gas sensor are highlighted.

11 April 2018 in Journal of Microelectromechanical Systems
Verified
Journal Article
Closed access
ALAyoub Lahlalia
Ayoub Lahlalia
ONOlivier Le Neel
Olivier Le Neel
RSRavi Shankar
Ravi Shankar
SKShian Yeu Kam
Shian Yeu Kam
Lado FilipovicLado Filipovic
Lado Filipovic
The microheater is an important part of a semiconducting metal oxide gas sensor, as its primary function is to heat up the sensitive layer to a desired temperature. The operating temperature of the sensor depends on the sensitive material used and the species of the target gases. Therefore, an accurate extraction of the sensor active area temperature as a function of the applied power is critical for device characterization. These measurements are experimentally challenging due to the extremely small sensing surface area, down to a few tens of μm², resulting in the need to develop new measurement approaches. In this paper, quantitative testing methods based on platinum and chrome silicon (CrSi) resistance thermometry, as well as a qualitative testing method (light glow) have been carried out to measure the power consumption of two different devices. CrSi has been used as a temperature sensor due to its ability to detect temperatures above 450 °C by acting as a phase-change material. For accurate measurements of temperature distribution, the presented gas sensors are equipped with three configurations of resistive temperature detectors at different locations. To further analyze a sample closed-membrane sensor, finite-element simulations were performed and an analytical model was designed and compared with experimentals. [2017-0228]

3 October 2011 in Journal of Microelectromechanical Systems
Verified
Journal Article
Closed access
MTMin Tang
Min Tang
YLYong Hean Lee
Yong Hean Lee
RKRakesh Kumar
Rakesh Kumar
RSRavi Shankar
Ravi Shankar
ONOlivier Le Neel
Olivier Le Neel
GNGiuseppe Noviello
Giuseppe Noviello
This paper presents design, fabrication, and characterization of a novel microelectromechanical microreed switch, which consists of two Ni80Fe20 magnetic plates as microreeds. One is embedded in a silicon trench. The other is suspended above the substrate and supported by a pair of crab-leg flexures from the two sides. Both Ni80Fe20 plates are split into two long, narrow strips to improve the sensitivity. The switch is actuated by bringing an external magnet closer to the switch. The magnetic field required to turn on the switch can be as low as 0.5 mT and the initial contact resistance is <; 10 Ω with gold contacts. The switch has been tested to pass more than 40 million hot switching cycles at 2 mA current at room temperature when packaged at wafer level with SU-8 sealing. The die size is 1.7 × 1.8 × 1.1 mm3. The proposed microreed switch can be used as the proximity sensor to sense the magnetic field. It also has the potential to replace the conventional reed switch in portable electronics, such as cellular phones, hearing aids, and laptops, where conserving battery power and device size is critical.

13 September 2010 in Journal of Microelectromechanical Systems
Verified
Journal Article
Closed access
MTMin Tang
Min Tang
ELEbin Liao
Ebin Liao
CCCheng Kuo Cheng
Cheng Kuo Cheng
DLDayong Lee
Dayong Lee
RKRakesh Kumar
Rakesh Kumar
FIFrancesco Italia
Francesco Italia
A passive magnetostatic microelectromechanical systems (MEMS) switch using only one electroplated soft magnetic layer of nickel-iron (Ni80Fe20) alloy was designed, fabricated, and characterized. The switch is composed of an electroplated Ni80Fe20 plate supported by a pair of torsion bars from two sides. The Ni80Fe20 plate is patterned into long and narrow strips to improve the sensitivity. The switch is actuated by bringing an external magnet closer to the switch. Therefore, no internal electrical power is consumed by the device for actuation. The magnetic field required to turn on the switch is 4.8 mT, and the initial contact resistance is 0.5 Ω with gold contacts. The switch has been tested to pass more than 34 million hot-switching cycles at 2-mA current at room temperature when packaged at the wafer level with SU-8 sealing. The die size is 2.1 × 1.94 × 1.1 mm3. The magnetic switch of this paper has the potential to replace the conventional reed switch in portable electronics such as laptops, cellular phones, personal data assistants, pacemakers, and hearing aids.

7 December 2018 in Proceedings
Verified
Conference Paper
Open access
PDF file
ALAyoub Lahlalia
Ayoub Lahlalia
ONOlivier Le Neel
Olivier Le Neel
RSRavi Shankar
Ravi Shankar
Siegfried SelberherrSiegfried Selberherr
Siegfried Selberherr
Lado FilipovicLado Filipovic
Lado Filipovic
Semiconducting metal oxide (SMO) gas sensors, dedicated to wearable devices were designed, fabricated, and characterized in terms of power consumption, thermal distribution, and sensing capability. The sensors demonstrate a sensitivity down to ppb-level VOC concentrations at a low power consumption of 10.5 mW. To further enhance the baseline stability and sensing response characteristics at low power consumption, a new sensor structure is proposed. The design implements novel aspects in terms of fabrication and microheater geometry, leading to improved sensor performance which enables new applications for SMO gas sensors. In this work, two designs were analyzed using experimental characterization and simulation. The results of the analyses of the two sensors are comparatively reported.