Active packaging that can extend the shelf-life of fresh fruits and vegetables after picking can assure food quality and avoid food waste. Such packaging can prevent the growth of microbial and bacterial pathogens or delay the production of ethylene, which accelerates the ripening of fruits and vegetables after harvesting. Proposed technologies include packaging that enables the degradation of ethylene, modified atmosphere packaging, and bioactive packaging. Packaging that can efficiently adsorb/desorb ethylene, and thus control its concentration, is particularly promising. However, there are still large challenges around toxicity, low selectivity, and consumer acceptability. Metal–organic framework (MOF) materials are porous, have a specific surface area, and have excellent gas adsorption/desorption performance. They can encapsulate and release ethylene and are thus good candidates for use in ethylene-adjusting packaging. This review focuses on MOF-based active-packaging materials and their applications in post-harvest fruit and vegetable packaging. The fabrication and characterization of MOF-based materials and the ethylene adsorption/desorption mechanism of MOF-based packaging and its role in fruit and vegetable preservation are described. The design of MOF-based packaging and its applications are reviewed. Finally, the potential future uses of MOF-based active materials in fresh food packaging are considered.
Three‐dimensional porous graphene (3D‐PG) has attracted much attention due to its excellent electrochemical performance. Chemical reduction is one of common methods for preparing porous graphene. In order to develop a green and facile method for preparing three‐dimensional porous graphene, in this paper, 3D‐PG was fabricated by reduction of graphene oxide (GO) with ascorbic acid (AA) as reductant in hydrothermal condition based on non‐toxic, non‐flammable and mild reducing performance of ascorbic acid. It was found that the size and distribution of pores could be controlled by the reduction time and the concentration of AA in the solution. The pore sizes in R0, R1 and R2 were in the range of 0.5–1 μm, 1–1.5 μm, and 1.5–3 μm, respectively. It was found that the average pore size and volume increased along with the amount of reductants. Under optimal conditions – a reaction time of 20 h and a ratio of GO to AA=1 : 1 – the CV area of the so‐obtained sample R1‐20 at 100 mV was 0.06 and the specific capacitance of the 3D‐PG electrode reaches 153.5 F ⋅ g−1, which is suitable for use in supercapacitors.
Hydrophobic and oleophobic materials have an important role in daily-life and industry. The hydrophobic and oleophobic property is mainly ascribed to the low surface energy materials and the roughness surface. The hydrophilicity and oleophobicity surface can be achieved by surface modification methods, such as electrodeposition, sol–gel process, chemical vapour deposition and spray deposition. In this paper, the properties of hydrophobic and oleophobic materials are introduced. The principles, characteristics and applications of surface modifications in hydrophobic and oleophobic materials are reviewed.
2,2′,7,7′-Tetrakis(N,N-di-p-methoxyphenyl-amine)-9,9′-spirobifluorene (spiro-OMeTAD) film currently prevails as hole transport layer (HTL) employed in perovskite solar cells (PSCs). However, the standard preparation method for spin-coated, Lithium bis(trifluoromethylsulfony) imide (LiTFSI)-doped, spiro-OMeTAD HTL depends on a time-consuming and uncontrolled oxidation process to gain desirable electrical conductivity to favor device operation. Our previous work demonstrated that ~10 s oxygen or oxygen containing gas discharge plasma exposure can oxidize spiro-OMeTAD HTL effectively and make PSCs work well. In this communication, hole-only devices are fabricated and in-situ current density-voltage measurements are performed to investigate the change in hole mobility of LiTFSI-doped spiro-OMeTAD films under plasma exposure. The results reveal that hole mobility values can be increased averagely from ~5.0 × 10−5 cm2V−1s−1 to 7.89 × 10−4 cm2V−1s−1 with 7 s O2 plasma exposure, and 9.33 × 10−4 cm2V−1s−1 with 9 s O2/Ar plasma exposure. The effects on the photovoltaic performance of complete PSC devices are examined, and optical emission spectroscopy (OES) is used for a diagnostic to explain the different exposure effects of O2 and O2/Ar plasma. High efficiency, fine controllability and good compatibility with current plasma surface cleaning techniques may make this method an important step towards the future commercialization of photovoltaic technologies employing spiro-OMeTAD hole transport material.