Commercial proton exchange membrane heavy-duty fuel cell vehicles will require a five-fold increase in durability compared to current state-of-the art light-duty fuel cell vehicles. We describe a new composite membrane that incorporates silicotungstic heteroply acid (HPA), α-K8SiW11O40▪13H2O, a radical decomposition catalyst and when acid-exchanged can potentially conduct protons. The HPA was covalently bound to a terpolymer of tetrafluoroethylene, vinylidene fluoride, and sulfonyl fluoride containing monomer (1,1,2,2,3,3,4,4-octafluoro-4-((1,2,2-trifluorovinyl)oxy)butane-1-sulfonyl fluoride) by dehydrofluorination followed by addition of diethyl (4-hydroxyphenyl) phosphonate, giving a perfluorosulfonic acid-vinylidene fluoride-heteropoly acid (PFSA-VDF-HPA). A composite membrane was fabricated using a blend of the PFSA-VDF-HPA and the 800EW 3M perfluoro sulfonic acid polymer. The bottom liner-side of the membrane tended to have a higher proportion of HPA moieties compared to the air-side as gravity caused the higher mass density PFSA-VDF-HPA to settle. The composite membrane was shown to have less swelling, more hydrophobic properties, and higher crystallinity than the pure PFSA membrane. The proton conductivity of the membrane was 0.130 ± 0.03 S cm−1 at 80 °C and 95% RH. Impressively, when the membrane with HPA-rich side was facing the anode, the membrane survived more than 800 h under accelerated stress test conditions of open-circuit voltage, 90 °C and 30% RH.
23 February 2024 in Journal of the Electrochemical Society
An anion exchange membrane water electrolyzer (AEMWE) was studied with three electrocatalysts (Co3O4, Mn2O3, MnO2) for the oxygen evolution reactions at 50 °C in 1 M K2CO3(aq). We employ an optimized robust high performance polymer based on a polyethylene mid-block copolymer, poly(vinylbenzyl-N‑methylpiperidinium carbonate)‑b‑polyethylene‑b‑poly(vinylbenzyl-N‑methylpiperidinium carbonate) as the AEM and the anode ionomer. The cathode utilized a high loading of Pt/C, 1 mg cm−2, to minimize contributions to the kinetics. We tested three catalyst loadings (0.5, 2.5, and 4.5 mg cm−2) with a fixed ionomer loading of 0.5 mg cm−2 to assess ionomer-catalyst interactions. The best-performing catalyst loadings were investigated in a 100 h durability test at 750 mA cm−2. The 2.5 mg cm−2 MnO2 catalyst displayed superior performance, with 2.40 ± 0.02 V at 1 A cm−2. In the 100 h durability test, the Mn2O3 catalyst showed a degradation rate of +269 ± 15 μV h−1, whereas Co3O4 and MnO2 showed −800 ± 157 μV h−1, −114 ± 15 μV h−1, respectively with no membrane thinning indicating a gradual improvement. The MnO2 electrode was further investigated in a 500 h test was conducted, revealing a voltage change rate of −21 μV h−1 for 24–375 h. Pre and post-test FTIR mapping revealed evolution of micrometer-sized morphology corresponding to templating by the Ni-foam electrode.
High temperature, low humidity fuel cell operation is one method of increasing the potential of commercialization of fuel cell vehicles. In order for performance to be suitable under these conditions, new polymer electrolyte membrane material needs to be synthesized and characterized. One particularly important property is water content. Water is an important aspect of polymer electrolytes, often having strong influence on ion transport and fuel cell performance. A novel material has been made, containing a heteropoly acid covalently bound to a fluoroelastomer. This material was analyzed with DVS to gain insight on water sorption. The data suggested that the water content is similar to Nafion® with respect to humidity, thus some other parameter is likely to cause improved performance under high temperature and low humidity operation.