27 November 2019 in Water Resources Research
Due to diagenesis, pores in subsurface rocks such as sandstones exhibit varying degrees of surface roughness in the forms of authigenic cement coatings and mineral dissolution. Previous work describing capillary trapping in porous media has primarily focused on pore‐space geometry, wettability, and fluid viscosity contrast, while acknowledging, but not quantifying, the potential impact of surface roughness. We introduce a method to implement surface roughness with controlled variation of hillock density and heights into glass microfluidic chips and investigate surface roughness impacts on gas trapping following imbibition of water into air. We demonstrate that surface roughness with hillock height‐to‐pore‐depth ratios (herein called Ω) less than a media‐dependent threshold (Ω = 6%–10% in the micromodels) does not promote nonwetting phase (gas) trapping. By contrast, rougher micromodels with Ω values larger than the aforementioned roughness threshold show a dramatic increase in the saturation of trapped gas (gas saturation values up to 64%) due to an observed change in imbibition dynamics from binary filling to pendular‐ring formation within pore throats as well as capillary pinning within pore bodies. Furthermore, when the micromodel intermediate capillary number results are compared to Land's model, only the roughest microfluidics chips (Ω > 10%) fall within the literature‐described values of the characteristic trapping constant, C, implying that surface roughness is also a key gas trapping control, independent of or in addition to pore‐space geometry and wettability. An a priori menisci stability criterion and a heuristic explanation based on local contact angle variations are proposed to explain surface roughness‐induced trapping.
29 June 2021 in Water Resources Research
Snap‐off is a phenomenon that occurs when a non‐wetting fluid is displaced by wetting fluid in pore‐throat channels, leading to the breakup of droplets at the throat. Snap‐off plays a key role in many industrial processes involving immiscible multiphase flows, such as aquifer remediation, carbon capture and geological storage, recovery of hydrocarbons. Here we derive geometric criteria for the capillary snap‐off at the pore‐throat junctions in 2D microchannels with rectangular cross‐sections. The criteria are theoretically presented in three categories according to the range of the throat depth, h. We find that if h is smaller than the throat width, snap‐off will be inhibited, if h is larger than the pore width, snap‐off may occur but it is independent of h, and if h is in between the throat width and the pore width, a critical depth exists for the occurrence of snap‐off. These criteria are verified using numerical CFD simulations and validated using microfluidic experiments. These results indicate the conditions for snap‐off in the pore‐throat channel with rectangular cross‐sections, which clarify previous debates in the literature. One application of this work is for micromodels, which are porous microfluidic chips used as tools to observe multiphase flow in porous media at the pore‐scale. Most micromodels are two‐dimensional (2D), which have rectangular cross‐sections with uniform depth. The geometric criteria derived here provide guidelines for the design of micromodels used in the study of multiphase flow processes in porous media.
2 July 2020 in Water Resources Research
Microfractures originate in hydrocarbon reservoirs and groundwater aquifers either in the form of pore‐scale authigenic apertures or secondary openings during well stimulation. Microfractures are often difficult to detect and can act as an invisible impediment when predicting hydrocarbon recovery. We use microfluidics to identify the flow conditions at which microfracture connectivity with macrofractures becomes impactful. The analysis focuses on fluid displacements at unfavorable mobility ratios, which are difficult to capture with high‐order numerical methods. Two configurations of microfracture type with the porous matrix, either dead‐end (only connected to one macrofracture) or connecting two macrofractures, were investigated as case examples for both water and oil‐wet conditions. Our findings confirm that improvements in hydrocarbon recovery are not universal due to the presence of microfractures but rather are a function of capillary number, wettability, and microfracture connectivity. We find that, regardless of wettability, a capillary number threshold for a connected microfractured system exists beyond which the effects of microfractures on recovery, fluid dendrite morphology, and oil ganglia number diminish considerably. However, substantial geometry‐dependent differences in recovery are observed below this threshold. A connected microfracture generally decreases hydrocarbon recovery and suppresses coalescence of viscous fingering dendrites regardless of wettability. In contrast, a dead‐end microfracture causes wettability‐dependent effects with (1) minimal impact on hydrocarbon recovery at water‐wet conditions and (2) both decreasing and increasing recovery effects at oil‐wet conditions. Furthermore, dead‐end microfractures become somewhat impactful to the divergence of viscous dendrites when capillary number increases but are overall ineffective to the trapped ganglia numbers.
1 October 2020 in Journal of Petroleum Science and Engineering
6 August 2021 in Water Resources Research
Polymer aqueous solutions are widely used in nonaqueous phase liquid recovery and aquifer remediation processes due to their high viscosity. Additional reduction of residual saturation by polymer's viscoelasticity has recently been discovered which elevates the ultimate displacement efficiency. However, there is no consensus on how, and under what conditions, viscoelasticity reduces residual saturation. This is in part because most studies utilize relatively low salinity and high viscosity, which also contribute to higher recoveries. We separate the effects of viscosity, elasticity and salinity, by performing microfluidic experiments in long (30 cm) heterogeneous glass micromodels (coreflood‐on‐a‐chip). In the experiments, a highly viscous Newtonian aqueous phase flood is first performed so that the system reaches residual saturation, followed by polymer flood with varying elasticity and salinity. This is followed by another highly viscous Newtonian aqueous phase flood. We observe significant redistribution and reconnection of residual ganglia due to viscoelasticity induced instabilities during high‐viscoelasticity polymer floods, which results in residual ganglia remobilization that ultimately reduces residual saturation. In contrast, no fluid redistribution and saturation reduction are observed in low‐viscoelasticity polymer floods. During low salinity polymer floods (regardless of the relative elasticity), spontaneous emulsification occurs inside ganglia and results in ganglia swelling, which enhances ganglia reconnection when elastic instability happens, therefore amplifies the residual saturation reduction.