Isaiah Adediji Adejumobi

Isaiah Adediji Adejumobi

Auto-generated profile, based on publicly available information

Isaiah Adediji Adejumobi

Federal University of Agriculture

Research Focus & Metrics

Academic Career Length

5Years (2022-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
16 October 2024 in International Journal of Electronics Letters
Verified
Journal Article
Closed access
ARAkeem Abimbola Raji
Akeem Abimbola Raji
JOJoseph Folorunso Orimolade
Joseph Folorunso Orimolade
IAIsaiah Adediji Adejumobi
Isaiah Adediji Adejumobi
KAKamoli Akinwale Amusa
Kamoli Akinwale Amusa
BOBakai Ishola Olajuwon
Bakai Ishola Olajuwon

1 September 2022 in International Journal of Advances in Applied Sciences
Verified
Journal Article
Open access
PDF file
KAKamoli Akinwale Amusa
Kamoli Akinwale Amusa
OIOlumayowa Ayodeji Idowu
Olumayowa Ayodeji Idowu
IAIsaiah Adediji Adejumobi
Isaiah Adediji Adejumobi
GAGboyega Augustine Adebayo
Gboyega Augustine Adebayo
Owing to methods of acquisition, medical images often require enhancement for them to serve the intended purpose of computer-aided diagnosis. Most medical image enhancement techniques are application specific, leading to the introduction of different enhancement methods for different medical images. In addition, the execution time of most of the previous enhancement methods is longer than necessary. Hence, there is a need for a method that produces fast and satisfactory results when deployed for the enhancement of several medical images. This paper proposes a tri-modal technique, involving a hybrid combination of unsharp masking, logarithmic transformation, and histogram equalization approaches, for medical image enhancement. Three classes of medical images: X-ray, magnetic resonance, and computer tomographic images are used for the evaluations of the proposed tri-modal method, where absolute mean brightness error, peak signal-to-noise ratio, and entropy are utilized as performance metrics. Both qualitative and quantitative evaluations reveal that the proposed tri-modal method performed better than the four previous methods in the literature for the three classes of medical images used in the evaluation. Also, the execution time of the tri-modal technique compares well with those of mono-mode methods. Thus, the tri-modal technique produces better enhanced medical images from different medical image inputs.

1 December 2023 in International Journal of Advances in Applied Sciences
Verified
Journal Article
Open access
PDF file
PAPhilip Oludele Awuwoloye
Philip Oludele Awuwoloye
IAIsaiah Adediji Adejumobi
Isaiah Adediji Adejumobi
OAOluwaseun Ibrahim Adebisi
Oluwaseun Ibrahim Adebisi
SISalami Olasunkanmi Ismaila
Salami Olasunkanmi Ismaila
One of the major challenges hindering the effective operation of the electricity distribution system is the malfunctioning of the protection scheme. Therefore, in this study, the performance of an interrupter (oil circuit breaker (OCB)) on the Eko Electricity Distribution Company (EKEDC) network was assessed. Five-year outage data (2014 to 2018) regarding tripping of the interrupter on fault and health conditions were collected from the EKEDC Agbara/Badagry Business Unit. The tripping frequency was compared. Inspection of selected OCBs within the considered network was conducted over the study period. A breakdown voltage (BDV) test was carried out on six oil samples each for 11 and 33 kV OCB using Megger OTS60PB. The highest tripping frequency of 75 and 10 were observed in 2014 and 2018 respectively when the interrupter tripped on fault and healthy conditions. The lowest tripping frequency was, however, observed in 2018 with values of 46 and 7 respectively when the interrupter tripped on fault and healthy conditions. The inspection conducted revealed carbonized OCB contacts. The BDV test showed that two oil samples each violated the standard value of 40 kV for 11 and 33 kV OCBs respectively. This study indicated that the defective oil samples required filtration or complete replacement.

1 December 2022 in International Journal of Electrical and Computer Engineering (IJECE)
Verified
Journal Article
Open access
PDF file
OAOluwaseun Ibrahim Adebisi
Oluwaseun Ibrahim Adebisi
IAIsaiah Adediji Adejumobi
Isaiah Adediji Adejumobi
SMSimeon Matthew
Simeon Matthew
AAAzeez Aderibigbe Abdulsalam
Azeez Aderibigbe Abdulsalam
In a developing nation like Nigeria, the conventional load monitoring and billing system has proved to be tedious, time-consuming, expensive, and prone to human error over the years. Therefore, this creates the need for an efficient system that can assist the Utility to monitor the energy consumption trend of the customers remotely. This work developed a web-based single-phase load monitoring and auditing system using NodeMCU (ESP8266) microcontroller, PZEM-004T sensor, and liquid crystal display (LCD) module for the hardware unit and Blynk internet of things (IoT) platform for the software unit. The system design was implemented around the ESP8266 microcontroller with relevant design models, and standard power and energy equations programmed into the microcontroller in the Arduino integrated development environment. The developed system was load tested to examine its performance and determine its reading error. The hardware and software units of the system operated satisfactorily when tested. The reading accuracy for current and voltage measured by the device were ±0.2% and ±0.4%, respectively, giving a reading error of ±0.8% for power measurement. The developed system is suitable for residential, commercial, and similar applications where the energy usage trend of some small loads is required for management purposes.

1 February 2023 in International Journal of Electrical and Computer Engineering (IJECE)
Verified
Journal Article
Open access
PDF file
OAOluwaseun Ibrahim Adebisi
Oluwaseun Ibrahim Adebisi
IAIsaiah Adediji Adejumobi
Isaiah Adediji Adejumobi
FDFolasade Olayinka Durodola
Folasade Olayinka Durodola
HJHaastrup Ayobami Jim
Haastrup Ayobami Jim
Road accident due to overspeeding is a common occurrence in a developing nation such as Nigeria. Therefore, the need for a device capable of notifying a vehicle driver when the allowed speed limit of an area is exceeded arises. In this work, a microcontroller based automobile speed limiting device and alarm control system was designed and developed. The core components employed for the system design include Arduino Nano microcontroller, 1602 liquid crystal displays (LCD) module, light-emitting diodes (LEDs), buzzer, 18650 battery, I2C, infrared detectors and push buttons. Data gathering and circuit designs were implemented with microcontroller as focal point using suitable design models. Performance test was carried out on the developed system and the device’s reading error was determined. The developed automobile speed limiting device and alarm control system was functional and performed satisfactorily during testing. The reading error of the device was evaluated as 5.83%. The developed speed limiting device, apart from being suitable and efficient for vehicle speed measurement, could also be deployed for general applications requiring speed measurement.