8 June 2022 in IEEE Transactions on Power Electronics
Although the wireless charging system (WCS) achieves flexible power transmission, high system operating performance needs strong anti-misalignment capability and excellent charging controllability. Hence, this article proposes a mistuned WCS that features dual transmission channels using half-bridge inverters, magnetic flux controlled inductors (MFCIs), magnetic couplers with hybrid coils (HMCs), and the series–series compensation. Then, high misalignment tolerance and high-efficient constant power (CP) charging are achieved. First, the interrelation among the mutual inductance, adjustable inductance, load resistance, charging power, and system efficiency is analyzed based on the optimally designed system structure. Second, the circuit structure and working principle of the MFCI are illustrated. Third, the anti-misalignment capability of the optimized HMC is verified by analyzing its coupling characteristics. Then, the relative spatial position between the two HMCs is determined to ensure the negligible cross-coupling influence. In addition, the closed-loop controller's working principle and design method is analyzed to achieve high-efficient and high-controllable CP charging within a wide range of misalignment distance and load resistance. Finally, the experimental results validate the feasibility of the proposed WCS. For CP charging of 150 W, x - and y -direction misalignment ranges reach ±95% and ±47%, and system efficiency exceeds 90%, superior to the commonly used anti-misalignment methods.
14 February 2023 in IEEE Transactions on Transportation Electrification
This paper proposes a wireless charging system (WCS) with the secondary-side interleaved Buck converter (SIBC) and multi-coil integrated solenoid magnetic coupler (ISMC). Then the constant current/constant voltage (CC/CV) charging based on SIBC duty cycle regulation is realized with high misalignment tolerance. First, the working principle and parameter design of the WCS is analyzed. Second, the ISMC structure is optimized, then the coupling condition comparison proves the high anti-misalignment capability. Besides, both the LCC inductor and SIBC filter inductors are integrated into the ISMC without affecting the power transfer. Third, the small-signal model of SIBC is set up, combined with the simulation results, the closed-loop control scheme for CC/CV charging is confirmed. Finally, the experimental results validate the feasibility of the proposed WCS with high performance.
26 September 2022 in Journal of Power Electronics
31 January 2025 in IEEE Transactions on Electromagnetic Compatibility
Digital control circuits failure problem usually occurs in electronic equipment working in a mixed electromagnetic environment. Therefore, it is necessary to study the failure mechanism of digital control circuits under mixed electromagnetic interference (EMI) and electromagnetic compatibility (EMC) design method to the failure problem. The digital circuit failure behaviors under mixed EMI of electrical fast transient (EFT) and surge are tested and analyzed. This article innovatively proposes an evaluation method of failure threshold of digital control circuits, that can be applied to the case where both voltage and current may change under mixed EMI of EFT and surge. The proposed evaluation method is dependent on the instantaneous product of amplitude and slope of the power supply port voltage of the regulator chip. The port voltage transfer characteristic of the regulator chip expressed using transfer function under mixed EMI is obtained. Then, the coupling model of mixed EMI of EFT and surge on the digital circuit board is built. The coupling model is validated by comparing the simulated results and measured results in 1000 V EFT and 20 V surge test. Based on the coupling model and the failure threshold, an evaluation method of circuit failure state under mixed EMI of EFT and surge is introduced and verified. Furthermore, an anti-interference filter design method is presented. Through a prototype experiment, the anti-interference filter design method is validated.
20 June 2024 in IEEE Transactions on Power Electronics
Desensitizing the misalignment and achieving low loss can improve the performance of wireless charging systems (WCS). A preference-based multiobjective optimization and resistance estimation algorithm based on the orthogonal table and multiple linear regression is used to achieve this. First, the working principle of a nonresonant WCS is analyzed to illustrate the relationship between WCS performance and mutual inductance along with coil resistance. Then, based on the orthogonal method and F-test, the parameters affecting the coil resistance are determined, and an estimation model for the coil resistance is established. Third, preference region and Latin hypercube sampling (LHS) are added to the nondominated sorting genetic algorithm II (NSGAII) method to enhance individual density within the preferred region without increasing the number of individuals and optimize the antimisalignment ability and coil resistance based on the model above of nested coils as an example using the proposed method. Compared to the NSGAII method, the mutual inductance fluctuation within 120 mm is reduced by 58% under similar conditions. Finally, the simulation and experimental results demonstrate that the proposed resistance estimation method has acceptable accuracy, and the proposed optimization method can optimize the horizontal antimisalignment ability of nested coils, and thus constant voltage/constant current charging is achieved.
23 September 2025 in IEEE Journal of Emerging and Selected Topics in Power Electronics
This article proposes a simple and efficient half-duplex simultaneous wireless power and data transfer (SWPDT) method using a multi-objective optimized magnetic coupler with high anti-misalignment ability. First, the working principle of the proposed SWPDT system, which needs to add extra components less than half of similar studies, is analyzed, and its requirements for magnetic coupler parameters to achieve a high signal-to-noise ratio (SNR) are given. Second, a target-based multi-objective particle swarm optimization with the k-means (T-MOPSO) method to achieve multi-objective optimization is analyzed, and a suitable magnetic coupler for rotating and lifting situations is designed. Third, the parameters of the magnetic coupler are optimized to achieve high misalignment tolerance and satisfy the requirements of SWPDT based on the T-MOPSO method. The experimental results show that the optimized magnetic coupler achieved a mutual inductance fluctuation of less than 6% within the range of 70 mm, exceeding 45% of the transmitter length, and the mutual inductance remains constant even when the receiver rotates. When the output power is more than 250 W, half-duplex communication with a data rate of more than 40 kbps to the receiver and 20 kbps to the transmitter, respectively, is achieved.