Osman Öztürk

Osman Öztürk

Auto-generated profile, based on publicly available information

Osman Öztürk

Konya Technical University

Research Focus & Metrics

Academic Career Length

5Years (2022-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
2 November 2022 in Journal of Composite Materials
Verified
Journal Article
Closed access
AÜAli Ünüvar
Ali Ünüvar
OÖOsman Öztürk
Osman Öztürk
The effects of cutting parameters on the thrust force and delamination factor in the drilling of pure, Al2O3, and SiO2 added GFRP/epoxy composites were investigated. Experimental studies were performed to investigate thrust force and delamination factor. Taguchi experimental design and response surface methodology were employed to establish parametric relationships between the experimental parameters and the machinability outputs consisting of delamination and thrust force. When examining the effect of cutting speed and feed on thrust forces and delamination factors for the three materials, the smallest values of the cutting parameters for all three materials gave the minimum thrust forces and delamination factors. Machinability Index is also proposed. According to the machinability index, under the effect of delamination and thrust force parameters, it was seen that pure epoxy composite material has better machinability than the other composite materials. It has been found that the effect of feed rate on delamination is greater than the cutting speed, and the cutting speed has a low effect.

14 January 2024 in Engineering Science and Technology, an International Journal
Verified
Journal Article
Open access
OÖOsman Öztürk
Osman Öztürk
MAMevlüt AYDIN
Mevlüt AYDIN
ÖGÖmer Faruk Gökcepınar
Ömer Faruk Gökcepınar
HIHarun Mert İlBeyli
Harun Mert İlBeyli
HKHabip Gökay Korkmaz
Habip Gökay Korkmaz
MTMevlüt Türköz
Mevlüt Türköz

20 November 2022
Verified
Book Chapter
Closed access
PDF file
OÖOsman Öztürk
Osman Öztürk
MŞMuhammed Arif Şen
Muhammed Arif Şen
MKMete Kalyoncu
Mete Kalyoncu
HHHüseyin Selçuk Halkacı
Hüseyin Selçuk Halkacı

15 September 2024 in Black Sea Journal of Engineering and Science
Verified
Journal Article
Closed access
OÖOsman Öztürk
Osman Öztürk
For drones, the use of which has been increasing recently for load carrying, lightweight drone frame design is significant for increased flight time and payload capacity. Drones are produced in different configurations with three, four, or six rotors, and in different sizes depending on the purpose of use. While agility is more important in three and four rotor drone applications, six-rotor and relatively large-bodied drones are preferred in cases such as load carrying. When the body structure has to be large, lightening the design becomes very critical. Lightweight designs can be achieved by two commonly used methods for structural optimization: topology optimization and parametric optimization. Topology optimization is an advanced method that can significantly reduce weight but is expensive and time-consuming. Parametric optimization is a more practical approach to conventional manufacturing methods and was used in this study. This study aims to first simplify the hexacopter frame model and define key geometric parameters for mass-decreasing optimization. Finite element analysis simulations were used to evaluate the strength and deformation of the frame under various design scenarios. The results showed that parametric optimization successfully reduced the weight of the hexacopter frame while maintaining structural integrity. The maximum Von Mises stress was found as approximately one quarter of the yield strength of the frame material. The maximum total deformation was achieved below 0.3 mm, and deformation under 1 mm is considered safe in the literature. As a result, the optimized design offers a lighter drone structure in line with conventional manufacturing methods, providing better flight time and payload capacity while maintaining cost effectiveness. In future studies, comparisons can be made based on this study by performing weight optimizations suitable for current methods such as topology optimization or generative design. The cost factor and the availability of existing production lines should be taken into consideration when comparing the mentioned methods with parametric optimization.

1 April 2024 in Konya Journal of Engineering Sciences
Verified
Journal Article
Open access
PDF file
OÖOsman Öztürk
Osman Öztürk
MŞMuhammed Arif Şen
Muhammed Arif Şen
MAMevlüt AYDIN
Mevlüt AYDIN
Fused Filament Fabrication (FFF) is a 3D (three-dimensional) printing technology that allows the production of polymers with a wide range of infill densities and unlimited geometric variations. Because of this flexibility, mechanical properties can be optimized by tuning printing parameters. However, the energy consumption during fabrication varies significantly for different printing settings. In the present study, both maximum fracture force and minimum energy consumption of 3D printed PLA (Polylactic Acid) are achieved together by optimizing the printing parameters using CPA (Cyclical Parthenogenesis Algorithm) optimization algorithm. Firstly, a quasi-static penetration test is performed to measure the maximum fracture force. The energy consumption of each specimen is also calculated. Then, maximum fracture force and energy consumption are modeled and integrated into the optimization algorithm. As a result, the three most convenient parameter levels are 84%, 6.83 mm, and 0.19 mm for infill ratio, specimen thickness, and layer height, respectively. While high infill ratio values and specimen thickness increase mechanical performance, these parameter levels are disadvantageous for energy consumption. As a result of optimization, parameters that provide balanced strength and energy consumption were obtained. Fracture force and energy consumption are 1829.87 N and 134.56 W, respectively for the validation experiment of the optimal solution.

3 December 2024
Verified
Book Chapter
Closed access
PDF file
OÖOsman Öztürk
Osman Öztürk
MŞMuhammed Arif Şen
Muhammed Arif Şen
MKMete Kalyoncu
Mete Kalyoncu
HHHüseyin Selçuk Halkacı
Hüseyin Selçuk Halkacı