Parul Rattanpal

Parul Rattanpal

Auto-generated profile, based on publicly available information

Parul Rattanpal

Electrical Engineering Department, Indian Institute of Technology Ropar, Rupnagar, Punjab, India

Research Focus & Metrics

Academic Career Length

5Years (2022-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
30 January 2024 in IEEE Transactions on Components, Packaging and Manufacturing Technology
Verified
Journal Article
Closed access
MKManoj Kumar
Manoj Kumar
SKSundeep Kumar
Sundeep Kumar
ASAshwani Sharma
Ashwani Sharma
VMVikas Kumar Malav
Vikas Kumar Malav
PRParul Rattanpal
Parul Rattanpal
The Wireless Power Transfer (WPT) rectenna systems suffer from low power conversion efficiency (PCE) due to lower receiver (Rx) gain, polarization mismatch, and angular misalignment that can occur between the transmitter (Tx) and receiver (Rx). This impedes the realization of self-sustaining freely-rotating IoT sensor nodes. To address this issue, an orthogonally-polarized, multi-beam, orientation-insensitive WPT system is proposed to achieve a nearly isotropic DC pattern. The system employs orthogonally-polarized end-fire rectennas (Rect-I & Rect-II) in each sector and a centrally placed cross-polarized patch rectenna (Rect-III) to attain 3D DC coverage. Further, the antenna and rectifier circuit are conjugately matched to achieve miniaturization. A fully integrated hybrid DC combining topology and a smart bypassing network is employed to minimize combining losses. The three rectenna elements offer a PCE of 51 %, 44.9 %, and 58.9 %, with an open-circuit harvested DC voltage of 1600 mV. Thus, orthogonally-polarized, nearly isotropic DC pattern and polarization insensitivity of the proposed multi-beam rectenna system (MBRS) makes it suitable for powering small battery-less IoT sensor nodes.

4 November 2025 in IEEE Internet of Things Journal
Verified
Journal Article
Closed access
PRParul Rattanpal
Parul Rattanpal
SGSumit Gautam
Sumit Gautam
ASAshwani Sharma
Ashwani Sharma
Combining insertion losses (CIL) and the non-linear (NL) behavior of rectification circuitry pose significant challenges to element splitting-based self-sustainable Reconfigurable Intelligent Surfaces (ESS-RIS) that utilize an RF-combining architecture for their energy harvesting (EH) elements. These factors not only degrade the end-to-end communication performance but also hinder the ability to meet ESS-RIS’s operational energy requirements. This work, therefore, proposes a novel clustering-based energy harvesting architecture for EH elements in an ESS-RIS that optimizes element allocation, enhancing both self-sustainability and overall communication efficiency compared to the state-of-the-art. Our findings demonstrate that the proposed architecture maintains a significantly higher signal-to-noise ratio (SNR) by reducing the fraction of RIS elements required for EH by a large percentage. Following this, a statistical analysis using the Marcum-Q function and the central limit theorem approximation is also performed for the proposed architecture to compare the results to the one obtained from exact simulations in MATLAB. To address the increased hardware demands in the proposed architecture, an optimization problem is formulated and tackled using three approaches, viz, Joint Parameter Optimization, Alternating Optimization, and the Genetic Algorithm. These methods aim to balance communication performance with hardware complexity effectively. Finally, a time complexity analysis is conducted to evaluate the asymptotic worst-case and best-case bounds of the proposed approach.

29 April 2022
Verified
Conference Paper
Closed access
PRParul Rattanpal
Parul Rattanpal
SSSukwinder Singh
Sukwinder Singh
This paper aims to design a multistage X band Power Amplifier design using a GaN HEMT active device from CREE-CGHV1J006D. The given amplifier is designed for a frequency 11.7 GHz. The output power of the three stage power amplifier was 4.8 W with Power Added Efficiency (PAE) close to 35%. This design is intended for space applications where a power amplifier module in the transmitter is the most power consuming device and, hence, should be able to minimize the power consumption with a better efficiency possible.

13 February 2026 in IEEE Transactions on Green Communications and Networking
Verified
Journal Article
Closed access
PRParul Rattanpal
Parul Rattanpal
ASAshwani Sharma
Ashwani Sharma
Reconfigurable Intelligent Surfaces (RISs) offer a low-cost, energy-efficient alternative to conventional repeaters and relays, enhancing wireless coverage and spectral efficiency through dynamic electromagnetic wave manipulation. The potential of a self-powered RIS is explored in the literature by employing element splitting (ES) on the RIS surface. This approach allocates some elements for beam steering, while the remaining elements are used for RF energy harvesting (EH) to meet RIS energy needs, aiming to create self-sustainable communication systems. The heuristic algorithms existing in the literature for such element allocation are valid only for ideal EH circuits, therefore, the proposed work incorporates combiner losses into the analysis to identify the most effective algorithm for maintaining system performance in terms of maximizing signal-to-noise ratio (SNR) and meeting the energy requirements of the RIS. Subsequently, the analysis reveals the necessity for a new loss-aware element selection algorithm (LA-ESA), which is proposed in this work. The results finally underscore the need for an innovative architectural paradigm shift in developing self-powered RIS, particularly in light of combiner losses. This shift is anticipated to enable a more robust software solution for self-powered RIS that meets hardware needs, thereby advancing the concept of self-sustainability and supporting environmentally friendly innovations in wireless communication.