Akash Subhash Awale

Akash Subhash Awale

Auto-generated profile, based on publicly available information

Akash Subhash Awale

Mechanical Engineering, Indian Institute of Technology (BHU), Varanasi, Department of Mechanical Engineering, Indian Institute of Technology (BHU) Varanasi-221005, Varanasi, Uttar Pradesh, 221005, INDIA

Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 August 2020 in Journal of Manufacturing Processes
Verified
Journal Article
Closed access
AAAkash Subhash Awale
Akash Subhash Awale
MVMeghanshu Vashista
Meghanshu Vashista
MYMohd Zaheer Khan Yusufzai
Mohd Zaheer Khan Yusufzai

9 June 2020 in Journal of the Brazilian Society of Mechanical Sciences and Engineering
Verified
Journal Article
Closed access
PDF file
AAAkash Awale
Akash Awale
KIKedar Inamdar
Kedar Inamdar

22 June 2022 in Journal of Manufacturing Science and Engineering
Verified
Journal Article
Closed access
PDF file
ACAbhimanyu Chaudhari
Abhimanyu Chaudhari
ASAshwani Sharma
Ashwani Sharma
AAAkash Subhash Awale
Akash Subhash Awale
MYMohd Zaheer Khan Yusufzai
Mohd Zaheer Khan Yusufzai
MVMeghanshu Vashista
Meghanshu Vashista
In the precision fabrication industries, ultrasonic vibration-assisted grinding is widely utilized for the finishing of “difficult-to-cut” materials due to its intermittent cutting mechanism and brittle-to-ductile mode machining. In this study, a two-dimensional finite element model (FEM) of single grit ultrasonic vibration-assisted dry grinding (UVADG) and conventional dry grinding (CDG) of AISI D2 steel has been developed, which taken into account the influence of longitudinal ultrasonic vibration on the workpiece with variable downfeed. The effects of ultrasonic vibration and downfeed on the chip formation mechanism, temperature field, grinding force, and equivalent stress and strain were evaluated by analytical and simulation methods. The results show that the formation of the grinding chips under UVADG is much shorter and straighter than CDG mode at all respective downfeed. The validation experiment compared the simulated and experimental grinding force in both grinding modes to verify the reliability of the FEM results. The validation results demonstrate that the FEM model can accurately describe the single grit UVADG and CDG grinding. At each downfeed, the CDG mode has generated a larger equivalent plastic strain than the UVADG mode, resulting in a higher thermomechanical load on the workpiece. According to the findings, UVADG mode has the least plastic damage on the ground surface, which may improve the surface integrity of the ground component.

1 September 2019 in Materials Research Express
Verified
Journal Article
Closed access
PDF file
ACAbhimanyu Chaudhari
Abhimanyu Chaudhari
AAAkash Subhash Awale
Akash Subhash Awale
ACAjit Kumar Chakrabarti
Ajit Kumar Chakrabarti

24 October 2018 in Materials Research Express
Verified
Journal Article
Closed access
PDF file
AAAkash Subhash Awale
Akash Subhash Awale
ASAshish Srivastava
Ashish Srivastava
MVMeghanshu Vashista
Meghanshu Vashista
MYM. Z. Khan Yusufzai
M. Z. Khan Yusufzai
Surface integrity has a significant effect on the service life of manufactured component as poor surface integrity may cause failure of produced component during its service life. Grinding is the last processing operation during manufacturing cycle of components, which decides the surface integrity of manufactured component. Surface quality of a component depends on the lubricating and cooling performance of cutting fluids during grinding. Thus the present research work investigates the effect of different lubrication modes like dry, flood, minimum quantity lubrication (MQL) on the surface properties of ground hardened H13 hot die steel. Surface integrity was evaluated in terms of surface roughness and microhardness of ground surface, ground surface topography, and microchip morphology. Where as, grinding performance was evalulated in terms of grinding force. The surface topography and elemental composition of ground surface along with microchip were observed using scanning electron microscope (SEM), atomic force microscope (AFM), and energy dispersive X-ray spectroscopy (EDX). Experimental results indicated that MQL with castor oil (CO) provided lowest surface roughness and grinding forces among all lubrication conditions, which were Rɑ-0.245 μm, Rz-1.846 μm, Ft-30.65 N, Fn-42.35 N, respectively. According to AFM analysis, poor surface quality (deep grooves and furrows) was observed under dry grinding due to micro-fractured abrasive grains and hard microchip rubbed over the ground surface. Continuous and smooth (no wear track) microchip was observed with MQL-CO lubrication. Further, EDX analysis indicated that microchips obtained upon MQL-CO lubrication were having very less carbon peaks without any surface oxidation. Higher microhardness was observed with MQL-DIW cooling due to suddenly quenching effect over the nascent ground surface.

26 November 2021 in Sādhanā
Verified
Journal Article
Closed access
PDF file
ACAbhimanyu Chaudhari
Abhimanyu Chaudhari
ASAshwani Sharma
Ashwani Sharma
AAAkash Subhash Awale
Akash Subhash Awale
MYMohd Zaheer Khan Yusufzai
Mohd Zaheer Khan Yusufzai
MVMeghanshu Vashista
Meghanshu Vashista