Yangjian Li

Yangjian Li

Auto-generated profile, based on publicly available information

Yangjian Li

State Key Lab of Fluid Power Transmission and Control, School of Mechanical Engineering, Zhejiang University, Hangzhou, China

Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 September 2019 in Energy
Verified
Journal Article
Closed access
YLYangjian Li
Yangjian Li
Hongwei LiuHongwei Liu
Hongwei Liu
YLYonggang Lin
Yonggang Lin
WLWei Li
Wei Li
YGYajing Gu
Yajing Gu

1 February 2020 in Ocean Engineering
Verified
Journal Article
Closed access
YLYangjian Li
Yangjian Li
WLWei Li
Wei Li
HLHongwei Liu
Hongwei Liu
YLYonggang Lin
Yonggang Lin
YGYajing Gu
Yajing Gu
BXBingling Xie
Bingling Xie

25 December 2019 in IEEE/ASME Transactions on Mechatronics
Verified
Journal Article
Closed access
Hongwei LiuHongwei Liu
Hongwei Liu
YLYangjian Li
Yangjian Li
YLYonggang Lin
Yonggang Lin
JBJingwei Bao
Jingwei Bao
WLWei Li
Wei Li
YWYaojun Wang
Yaojun Wang
Wave energy is one of the most important potential sustainable energy resources. To enhance the performance of pendulum hydraulic WEC (wave energy converter) system in various wave conditions, this paper proposes a digital controlled hydraulic cylinders group to replace the single traditional hydraulic cylinder in hydraulic PTO (power take-off) system based on the concept of previous study. The cylinders group, whose structure is designed with high extendability, consists of several pairs of subsidiary cylinders. The extraction energy maximizing for pendulum WEC is theoretically analyzed in frequency domain based on linear wave assumption, which indicates demand for damping regulation. The proposed cylinders group is able to provide variable damping for PTO system by changing its working area. So as to demonstrate the better performance of proposed cylinders group compared with single traditional hydraulic cylinder, a simulation in AMESim software and a fundamental semi-physical test have been carried out. Both results illustrated that the WEC was endowed with high performance by using cylinders group in various wave conditions. In addition, a transmission efficiency test indicated the application of cylinders group didn't cause much more extra energy loss during the transmission process compared with single traditional cylinder. The further study of cylinders group with more subsidiary cylinders and the control strategy remains to be conducted.

1 July 2020 in Ocean Engineering
Verified
Journal Article
Closed access
HLHongwei Liu
Hongwei Liu
YLYangjian Li
Yangjian Li
YLYonggang Lin
Yonggang Lin
WLWei Li
Wei Li
YGYajing Gu
Yajing Gu

22 May 2020 in Energies
Verified
Journal Article
Open access
PDF file
Hongwei LiuHongwei Liu
Hongwei Liu
YGYajing Gu
Yajing Gu
YLYonggang Lin
Yonggang Lin
YLYang-Jian Li
Yang-Jian Li
WLWei Li
Wei Li
HZHongbin Zhou
Hongbin Zhou
The efficiency and reliability of blades are key indicators for a tidal current turbine (TCT). A traditional blade design is often an empirical design on hydrodynamics and structure, sequentially. A hydrofoil with a low lift–drag ratio is considered when the structural strength cannot satisfy requirements. However, efficiency is then sacrificed. A redundant design is generally adopted to protect from load uncertainty, but this increases blade weight and cost. In this paper, we present an improved blade design method to enhance the blade reliability of TCTs with relatively high efficiency for energy generation. An equivalent S–N curve model describing the relationship between axial load and cycle times and a simplified load spectrum including load caused by shear flow and turbulence are proposed for the first time for convenient lifetime estimation. A multi-objective genetic algorithm is used to optimize the chord length, twist angle, and thickness of the blade for the best match between lifetime and efficiency. This blade design method was conducted on a 4.4 m length blade of a 120 kW TCT. Comparisons between the original design and optimal designs indicate that the comprehensive performance in terms of the hydrodynamics, structure, and lifetime of the blade presented significant improvements with a small, acceptable efficiency loss. The results also provide more alternative blade solutions for developers as a reference.

11 January 2023 in Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture
Verified
Journal Article
Closed access
YLYangjian Li
Yangjian Li
LZLiang Zhu
Liang Zhu
XZXuechun Zhang
Xuechun Zhang
HMHidenobu Maehara
Hidenobu Maehara
YZYangyan Zhang
Yangyan Zhang
To reduce the manufacturing cost of integrated circuits, the size of the silicon wafer has become larger, with the diameter increasing from 200 to 450 mm. The large diameter silicon wafer poses challenges to the manufacturing process, as its surface profile is more difficult to control and the planarization process is harder to optimize in mass production. Based on different types of contact, gap adjustment and convex pad dressing methods were proposed in this paper to control the pressure distribution on the wafer, which further influenced the wafer profile. Pressure distributions with different gap values and different pad profiles were explained with contact mechanics and verified by simulations. The simulation results show that a negative gap value and a convex pad profile contribute to the improvement of the pressure uniformity on the wafer. Both methods were then applied in the double-sided planarization (DSP) process of 300 mm silicon wafers. The results from the test run of the DSP process show that wafer flatness is improved with a negative gap value. This indicates that gap adjustment is an effective approach for wafer profile control. In the subsequent mass production of the DSP process, silicon wafers with a global flatness of 120 nm and a site flatness of 21.7 nm were obtained.