Magnetic shape memory alloys (MSMAs) are interesting materials because they exhibit large recoverable strain (up to 10%) and fast response time (higher than 1 kHz). MSMAs are composed of martensitic variants with tetragonal unit cells and a magnetization vector that is approximately aligned with the short side of the unit cell in the absence of an external applied magnetic field. These variants reorient either to align the magnetization vector with an applied magnetic field or to align the short side of the unit cell with an applied compressive stress. This reorientation leads to a mechanical strain and an overall change in the material’s magnetization, allowing MSMAs to be used as actuators, sensors, and power harvesters. This paper builds upon the work of Kiefer and Lagoudas as well as improvements proposed by LaMaster et al. to present a thermodynamic-based continuum model able to predict the response of an MSMA to any three-dimensional (3D) magneto-mechanical loading. The 3D nature of the model requires that the three variants, associated with the three axes of an MSMA single crystal, should all be allowed to evolve. In addition, this model includes evolution rules for the three magnetic domain volume fractions and the rotation of the direction of the magnetization vectors in each variant based on thermodynamic requirements.
18 January 2012 in Journal of Vibration and Acoustics
This paper presents a dual-mode magnetorheological (MR) fluid mount. Combining the fluid’s flow and squeeze modes of operation gives this MR mount a unique possibility for varying dynamic stiffness and damping. Details on the design of the internal structure of the mount and the magnetic circuit are provided. Simulation and experimental results are presented to show the effectiveness of the magnetic circuit. A mathematical model that combines the behavior of the fluid and the elastomeric parts and takes into account the magnetic activation of the fluid is used to gauge the effect of design parameters on the isolation characteristics of the mount. Experimental results show that in the proposed design, the dynamic stiffness of the mount may be varied over a wide range of frequencies making the mount a unique and versatile vibration isolation device for cases where input excitation occurs over a wide range of frequencies.
The martensite variant reorientation in Ni 2 MnGa magnetic shape memory alloys (MSMAs) causes a change in their bulk magnetization, that can be harvested into useful voltage/power by means of a pick-up coil. The coil may be placed directly surrounding an MSMA element or to the side of the MSMA element wrapped around a magnetic core. This paper reports new power harvesting data generated with a bi-axial magnetic field and a surrounding coil and full strain field data for an MSMA subject to load similar to what is seen during power harvesting, then compares the performance of MSMA-based power harvesters with different designs to determine which give the best output. For this comparison, we provide a framework for evaluating the performance of MSMA-based power harvesters reported in the literature. This framework involves normalizing the results to the design characteristics of the respective harvesters, i.e. number of turns of the pickup coil, cross-sectional area of the pickup coil, frequency of excitation, and sample size, to allow for a direct comparison of power harvesters’ output. Results show that power harvesting with the bi-axial field and a surrounding coil does not generate as much power as previously thought. The strain maps reveal the potential for perpendicular twin boundaries that block each other’s motion limiting variant reorientation and correspondingly the harvester’s power output. The paper concludes that the largest change in magnetic flux density, which is the driver for power harvesting, occurs in the side coil setup with an optimized magnetic circuit and it recommends using this configuration for future MSMA-based power harvester designs for maximum power output.
Ni–Mn–Ga is a ferromagnetic alloy that can exhibit the shape memory effect or superelasticity in the presence of a magnetic field. The behavior of the material is largely due to its microstructure, which is thought to be made of tetragonal martensite variants, each exhibiting an innate magnetization aligned approximately with the short side of the unit cell. Because the reorientation strain can be induced and recovered by either magnetic field or mechanical stress, it can be induced at frequencies larger than 1 kHz, which makes the material suitable for high-frequency actuation, sensing, or power harvesting applications. This paper investigates the power harvesting capability of Ni–Mn–Ga wrapped with a pick-up coil under a bi-axial magnetic field. In this work, both experimental tests and numerical simulations are used to identify the optimal direction of the externally applied magnetic field in order to achieve maximum open-circuit voltage output from a particular Ni–Mn–Ga based power harvester. Results suggest that significantly more power can be achieved with the bias field applied at an angle of 10°–20° off the perpendicular to the coil axis and the compressive stress. We believe that this increased power output is due to the saturation of domain walls due to a small component of the magnetic field along the direction of the coil.